Siemens SWT-3000 - Appendix; List of Figures

Installation and Commissioning SWT 3000 Equipment Manual
Appendix:
List of figures:
Figure 1: View of a SWT 3000 backplane without FOM slots -------------------------------------------------------------- 8
Figure 2: Equipment of the sub rack with two SWT 3000 systems---------------------------------------------------------- 9
Figure 3: View of a SWT 3000 backplane with FOM slots -----------------------------------------------------------------10
Figure 4: Equipment of the sub rack with a SWT 3000 system for using FOM modules -------------------------------11
Figure 5: Contact assignment of the interface module IFC-x --------------------------------------------------------------12
Figure 6: Connection principle for the binary inputs of the IFC-D/P modules ------------------------------------------12
Figure 7: Connection sockets X1 and X2 for the digital interfaces--------------------------------------------------------14
Figure 8: Position of jumpers X43 to X58 ------------------------------------------------------------------------------------20
Figure 9: Position of the jumpers on the PU3f module ---------------------------------------------------------------------21
Figure 10: Position of the jumpers on the DLE module ----------------------------------------------------------------------21
Figure 11: Position of the jumpers on the CLE module ----------------------------------------------------------------------23
Figure 12: Position of the LED on the FOM-----------------------------------------------------------------------------------24
Figure 13: The fibre optic box ---------------------------------------------------------------------------------------------------25
Figure 14: Position of the jumper and LED on the FOB module------------------------------------------------------------26
Figure 15: Display and setting elements on the ALR module----------------------------------------------------------------28
Figure 16: Position of the jumpers on the ALRS module ---------------------------------------------------------------------29
Figure 17: Possible cable variants for the connection of the service PC --------------------------------------------------32
Figure 18: Setting the PU3f output level.---------------------------------------------------------------------------------------33
Figure 19: Setting options for the protection transmit level for connection via VFx module --------------------------34
Figure 20: Connecting cable between the SWT 3000 and the VFx module ------------------------------------------------34
Figure 21: Connecting an external SWT 3000 to the port 3 of the VFx modules------------------------------------------35
Figure 22: Connecting an external SWT 3000 to the port 4 of the VFx modules------------------------------------------35
Figure 23: Connection of the SWT 3000 via FOM ----------------------------------------------------------------------------36
Figure 24: Setting of the analog interface of the SWT 3000 for the FOM connection to the PowerLink --------------36
Figure 25: SWT 3000 system-2 configuration for FO connection to the PowerLink -------------------------------------37
Figure 26: iSWT 3000 system-2 configuration for FO connection to the PowerLink ------------------------------------37
Figure 27: The PU3f is connected via the serial synchronous interface (SSI) with the CSP ----------------------------38
Figure 28: SWT 3000 connection via FOM ------------------------------------------------------------------------------------39
Figure 29: Example of a system configuration for a FOM connection with 64kbps--------------------------------------39
Figure 30: SWT 3000 connection via FOM to a multiplexer ----------------------------------------------------------------40
Figure 31: System configuration of the digital interface for the connection to a FOBox (example)--------------------40
Figure 32: Setting the input level attenuation----------------------------------------------------------------------------------41
Figure 33: Setting the alarm thresholds. ---------------------------------------------------------------------------------------42
Figure 34: Setting of date and time of an SWT 3000--------------------------------------------------------------------------43
Figure 35: Options for the SWT 3000 clock synchronisation ----------------------------------------------------------------43
Figure 36: Activation of NU alarm in case of USYNC failure---------------------------------------------------------------44
Figure 37: Possibilities for the clock synchronisation------------------------------------------------------------------------45
Figure 38: New configuration of the SWT 3000 -------------------------------------------------------------------------------46
Figure 39: Selecting the software package-------------------------------------------------------------------------------------46
Figure 40: Creating a database -------------------------------------------------------------------------------------------------46
Figure 41: Input tabs for an SWT 3000-----------------------------------------------------------------------------------------47
Figure 42: Menu for the SWT 3000 system configuration--------------------------------------------------------------------47
Figure 43: Defining the IFC interface modules -------------------------------------------------------------------------------49
Figure 44: Output allocation for operating mode Mode M5A---------------------------------------------------------------50
Figure 45: RM Configuration menu---------------------------------------------------------------------------------------------51
Figure 46: The SWT 3000 timer tab---------------------------------------------------------------------------------------------52
Figure 47: Setting options for the command input ----------------------------------------------------------------------------53
Figure 48: Example for input limitation set to 50 ms -------------------------------------------------------------------------53
Figure 49: Example for an input command extension to min 15ms. --------------------------------------------------------54
Figure 50: Setting options for the pulse suppression -------------------------------------------------------------------------55
Figure 51: Example for a pulse suppression of 5 ms--------------------------------------------------------------------------55
Figure 52: Setting options for limitation of the output command -----------------------------------------------------------56
Figure 53: Example of an activated output command limitation ------------------------------------------------------------56
Page - 68 Edition p3_3_2x 08/09 © SIEMENS AG 2008