Smeg WD7010 - Page 153

To Next Page

To Previous Page

USER MANUAL

WD6010 – WD7010 – WD7015

Page 153 - 168

EXAMPLE OF CORRECT INSTALLATION

N.B.: As specified in the "Installation Requirements" document, the water inlet taps must be set to one

side (not directly above the machine) so that any leaks or drips do not fall on top of the device.

Main Page

Table of Contents2
Initial Reccomendations7
Service Life8
Intended Use and Classification8
Intended Use8
Wd Classification9
Standard 1588310
Definition: "Responsible Body" of the Device11
Type Operator and "Superuser11
Presentation12
WD6010 and GW6010 - MACHINE with SWINGING DOOR13
Wd7010 - Gw7010, Wd7015 - Gw7015 - Machine with Sliding Doors16
Optional Barcode Scanner - Wd-Codescan20
Configurations and Optionals22
Models Without Steam Heating23
Models Equipped with Steam Heating System24
50Hz Models25
60Hz Models26
WD7015 Models 50Hz, 400V 3N27
WD7015 Models 50Hz, 230V 328
WD7015 Models 60Hz29
Safety and Handling Precautions30
Key to the Symbols Used in the Manual and on the Machine30
General Recommendations32
Automatic Loading and Unloading Systems Cb7015 System Safety Precautions34
Recommendations for Transport35
Accessing and Reusing the Device after an Incomplete Cycle37
Use of the Release Trolley37
Door Opening, Door Closing38
Wd601038
Wd7010 - Wd701540
Manual Door Unlock42
Operating Procedures43
Access to Detergent Compartment43
Wd6010 - Gw601044
Wd7010 - Gw7010 - Wd7015 - Gw701545
Use of Detergents45
Liquid Detergent Suction System46
Detergents47
Load Preparation for Wash Cycle and Disinfection49
Basic Operations52
Home Screen - ID 1.0.0.052
Door Control - Machines with Hinged Doors52
Door Control - Machines with Sliding Doors52
Programs Complete Menu - ID.1.1.0.054
Favourite Programs Menu - ID.1.1.0.054
Program Start - ID. 1.1.1.054
External Perimeter Buttons and Data55
Internal Perimeter" Screen Data55
Selected Cycle Options - ID. 1.6.1.056
Cycle Start - "User Check" Function Active57
Notes57
Barcode Acquisition - Wd-Codescan58
Program under Way - 1.1.1.360
Subphases in Progress62
Program in Progress "Display Easy"- 3.4.2.162
Completed Program - 1.1.1.463
Operation in Combination with Energy Management64
System Active - Power to Start Program Not Available65
Network Problems and Disabling the System - Superuser66
Energy Management - Unloading ("Clean") Side Screen67
Setup Operation - 1.4.0.068
Set up Date and Time - ID.1.4.2.170
Enter Password - ID.1.5.0.471
Language Selection - ID. 1.4.2.271
Counters - ID. 1.4.6.172
Archive and Printer - ID 1.4.6.273
Cycles Archive Download to Usb Drive76
Machine Parameters - ID. 1.4.2.080
DETERGENT DOSAGE SETUP ("Chemicals Dosing") - ID. 1.4.2.381
PROGRAMS ACTIVATION ("Programs Enable") - ID. 1.4.6.0 - 1.4.6.482
Password - ID. 1.5.0.184
Lan Parameters - ID. 1.4.8.0 - 1.4.8.285
FULL S/N, MAC, ID (Device Labels) - ID. 1.4.8.186
Diagnostics Operations - ID.1.4.3.088
Programs Editing - ID. 3.4.2.190
Customizing the Program Name93
Customizing the Program Icon93
New Program Parameter: "Passing / Not Passing" Flag94
Display and Sounds - ID. 3.4.2.196
About - ID. 1.4.5.0 - 1.4.5.197
User Password - ID. 150397
Heating Type - ID. 146599
Water Conductivity - ID.1466100
Purpose of the Accessory101
Operation of the Machine with the Probe Active: Conductivity Check Function101
Trolley Check - ID.14A0103
Operation with Optional Active - Trolley Check107
Spray Arms Check - ID 14A0109
Spray Arms Check - Cycle in Progress111
Automatic Operation - ID.146B112
Management of Automatic Loading and Unloading System - Cb7015113
AUTOMATIC OPERATION and ENERGY MANAGEMENT SOFTWARE - ID.146B - 146C115
Barcode Scanner - Superuser Parameters115
SIGNAL BOX, OPTIONAL Prod. Ref. "WD-SIGNBOX117
ALARMS and WARNINGS118
Warning - ID 1.1.1.2119
Warnings Linked to Cb7015121
Warning Related to the Energy Management Software122
Alarms - ID 1.1.1.6124
Cleaning and Maintenance135
Preliminary Warning135
CLEANING of the DEVICE and Its Parts135
Cleaning of the Filter Unit139
In Case the Device Remains Unused140
Device Re-Use after a Period of Idleness141
Time Schedule for Routine Maintenance and Checks142
Daily142
Weekly142
Every Six Months142
Every Year142
Elimination of Small Trouble143
Installation144
PACKAGE REMOVAL and PREPARATION for MOVEMENT144
Positioning and Leveling146
Single Door" Machine148
Double Door" Machine149
Electrical Wiring Regulations151
Access to the Electrical Cable and to the Water Charging Hoses152
Access from Top of Device152
Access from Rear154
Water System Setup157
Water Load157
Demineralized Water158
Water Drain159
Steam System Connection (Optional)162
Chamber Vent Connection (Air and Steam)163
Technical Characteristics164
Manufacturer References and After-Sales Service168

Smeg WD7010 - Page 153

Table of Contents

Other manuals for Smeg WD7010

Related product manuals