Sony MLS-X1 - Page 367

367
Specify the knee point position and slope of the
curve.
HDR Contrast: HDR contrast level corresponding to SDR
1
00% level (display only)
HDR Gain (dB): Gain when converting from SDR to
HDR
When the conversion mode is [Display Referred], the
hi
ghlight creation function cannot be set.
1 Open the Home > Setup > System > Format/Config >
HDR/SDR Format menu (19101.23).
2 Enable/disable the highlight creation function using
the [Highlight Creation] button.
On:
Enable the highlight creation function.
Off: Disa
ble the highlight creation function.
When disabled, proceed to step 5.
3 Press the [Point (Abs.)] button and select a knee point
position for the curve from the pull-down list.
4 Press the [Slope (Abs.)] button and select a slope for
the curve from the pull-down list.
5 Press the [HDR Gain (dB)] button and enter a gain
value in the numeric keypad window.
To set the HDR Look function
You can set the visual appearance of the HDR image on a
di
splay.
1 Open the Home > Setup > System > Format/Config >
HDR/SDR Format menu (19101.23).
2 Press the [HDR Look] button and select a type of look
from the pull-down list.
Live: Vi
vid images with high contrast and color
saturation.
Mild: Gen
erally more mild images than that
produced using [Live].
Natural:
Images with reduced sensitivity, but which
is less affected by noise.
When the OETF is set to [PQ], [S-Log3 (HDR)], or
[
S-Log3 (Live HDR)], [Natural] cannot be set.
To set the HDR black compression function
You can enable the black compression function and
adj
ust the HDR black level so that it is the same as for
SDR.
1 Open the Home > Setup > System > Format/Config >
HDR/SDR Format menu (19101.23).
2 Enable/disable the black compression function using
the [HDR Black Comp.] button.
On: E
nable the black compression function.
Off:
Disable the black compression function.
To set the HDR black level
1 Open the Home > Setup > System > Format/Config >
HDR/SDR Format menu (19101.23).
2 Press the [Master Black (Abs.)] button in the [Black
Level] group and enter a master black value in the
numeric keypad window.
3 Press the [HDR Black Offset] button in the [Black
Level] group and enter an HDR black offset in the
numeric keypad window.
Setting SDR
You can configure SDR when the OETF is set to [SDR].
Knee: Knee function when converting from HDR to SDR
The knee is a function that compresses high
l
uminance areas.
Specify the knee point position and slope of the
curve
.
White Clip: White clip function when converting from
HDR
to SDR
Specify the level of the video signal.
HDR Contrast: SDR contrast level corresponding to HDR
100
% level (display only)
SDR Gain (dB): Gain when converting from HDR to
SD
R
Gamma (Table): Type of gamma curve
Select from standard gamma and hypergamma.
When the conversion mode is [Display Referred], the
ty
pe of gamma curve cannot be set.
1 Open the Home > Setup > System > Format/Config >
HDR/SDR Format menu (19101.23).
2 Enable/disable the knee function using the [Knee]
button.
On: E
nable the knee function.
Off:
Disable the knee function.
When disabled, proceed to step 5.
3 Press the [Point (Abs.)] button and select a knee point
position for the curve from the pull-down list.
4 Press the [Slope (Abs.)] button and select a slope for
the curve from the pull-down list.
Note
Note
Note