VS1 VS2 VSM
VS3
43
VS1
VS1
VS1
VS2
VS2
VS2
VSM
VSM
VSM
VS3
VS3
VS3
M9047
○
○
○
○
○
○
○
○
○
○
○
○
■
M9048
M9049
Step Ladder Instruction Correlated Flags
Interrupt Prohibit Flag
Error Message
STL monitoring is enable. D9040~D9047 will be active only when M9047=“ON”.
The annunciator monitoring has been enabled. When M9049=“ON” and any coil of S900~S999=
“ON”, than M9048=“ON”.
Enable annunciator monitoring. D9049 will be effective only when M9049=“ON”.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
M9040
M9050
M9068
M9051
M9052
M9053
M9054
M9055
M9056
M9057
M9058
M9059
M9060
M9061
M9062
M9063
■
M9046
To prevent the step transfer. When M9040=“ON”, the STL state transfer function is disabled.
STL step is working. When M9047=“ON” and any relay of S0~S899=“ON” than M9046=“ON”.
■
M9066
■
M9067
VS1
VS1
VS2
VS2
VSM
VSM
VS3
VS3
Loop Counter
Pulse Measurement
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
M9072
M9099
M9076
M9077
M9078
M9079
M9080
■
M9075
○
○
○
○
○
○
M9167
M9168
Assign the HKY instruction operating mode. When M9167=“OFF”, by the “DEC” numeric mode;
when M9167=“ON”, by the “HEX” numeric mode.
Assign the SMOV instruction operating mode. When M9168=“OFF”, by the “DEC” numeric mode;
when M9168=“ON”, by the “HEX” numeric mode.
○ ○ ○
M9165
Assign the SORT2 instruction operating mode. When M9165=“OFF”, the sort is by ascending
order; when M9165= “ON”, by descending order.
○
○
○
○
○
○
○
○
○
○
○
M9160
M9161
Assign the XCH to execute the SWAP function.
Assign the 8-bit or 16-bit operating mode for the related instructions. When M9161=“OFF”,
those instructions are processed by the 16-bit mode; when M9161=“ON”, are by the 8-bit mode.
M9091
Assign the BINDA operating mode.
16-bit instruction: If M9091= “OFF”, will add the end of string 0000H after the result.
If M9091=“ON”, will only convert the data without to add the end of string.
32-bit instruction: If M9091=“OFF”, will add the end of string 00H at the result's last upper 8 bits.
If M9091=“ON”, will add the end of string 20H at the result's last upper 8 bits.
○
Assigning Specification of Applied Operation Instructions Mode
To prevent the external interrupt from IX0. The IX0P or IX0F is prohibited.
To prevent the external interrupt from IX1. The IX1P or IX1F is prohibited.
To prevent the external interrupt from IX2. The IX2P or IX2F is prohibited.
To prevent the external interrupt from IX3. The IX3P or IX3F is prohibited.
To prevent the external interrupt from IX4. The IX4P or IX4F is prohibited.
To prevent the external interrupt from IX5. The IX5P or IX5F is prohibited.
To prevent the external interrupt from IX6. The IX6P or IX6F is prohibited.
To prevent the external interrupt from IX7. The IX7P or IX7F is prohibited.
To prevent the timer interrupt ITA. The ITA □□ for timer interrupt is prohibited.
To prevent the timer interrupt ITB. The ITB □□ for timer interrupt is prohibited.
To prevent the timer interrupt ITC. The ITC □□ for timer interrupt is prohibited.
To prevent the SHSCs' interrupt. Software High Speed Counter interrupts IHC0~7 are prohibited.
To prevent the HHSC1's interrupt. Hardware High Speed Counter interrupt IHHC1 is prohibited.
To prevent the HHSC2's interrupt. Hardware High Speed Counter interrupt IHHC2 is prohibited.
Program CHECK SUM error will cause the PLC stop, M9066=“ON” and “ERR” indicator ash (2Hz).
Operation error. If operation error occurs during program execution, then M9067=“ON” but PLC
will keep running.
Operation error latch. When M9068=“ON” and operation error occurs, the step number where
operation error occur will be latched in D9068,D9069.
Start the 32-bit up-count loop counter 0~2,147,483,647. (unit: ms)
Start the 16-bit high-speed-up-count loop counter 0~32,767. (unit: 0.1ms)
Pulse measurement setting-up ag. Use this ag contact to active the pulse width / period
measurement function at the X0, X1, X3 or X4.
To start the X0 for pulse measurement.
To start the X1 for pulse measurement.
To start the X3 for pulse measurement.
To start the X4 for pulse measurement.
To set the mode of X0's pulse measurement. “OFF”: pulse width measurement,
“ON”: pulse period measurement
Description
Relay ID
No.
Series
To Next Page
Loading...
Need help?
General