VS1
VS1
VS1
VS1
VS2
VS2
VS2
VS2
VSM
VSM
VSM
VSM
VS3
VS3
VS3
VS3
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
M9200
M9234
〜
M9235
M9245
〜
■
M9246
■
M9255
〜
M9260
M9279
〜
45
VS1 VS2 VSM
VS3
M9332
○
○
○
M9334
○
○
M9330
M9331
M9333
VS1
VS1
VS2
VS2
VSM
VSM
VS3
VS3
○
○
○
○
○
○
○
○
M9280
M9299
〜
M9300
M9319
〜
The 32-bit Counter Count Direction Control
Controlling Flag of Software High Speed Counter Count Direction
Monitoring Flag of Software High Speed Counter Count Direction
Working Area of the EC1 Expansion Card
Working Area of the EC2 Expansion Card
Working Area of the EC3 Expansion Card
DUTY Instruction Output
When M92 □□ =“OFF”, the C2 □□ is operated as a up counter.
When M92 □□ =“ON”, the C2 □□ is operated as a down counter.
When M92 □□ =“OFF”, the C2 □□ is operated as a up counter.
When M92 □□ =“ON”, the C2 □□ is operated as a down counter.
When C2 □□ is operated a up count, M92 □□ =“OFF”.
When C2 □□ is operated a down count, M92 □□ =“ON”.
EC1 Expansion Card's working area. M9260~M9267= EC1X0~EC1X7;
M9270~M9277=EC1Y0~EC1Y7.
EC2 Expansion Card's working area. M9280~M9287= EC2X0~EC2X7;
M9290~M9297=EC2Y0~EC2Y7.
EC3 Expansion Card's working area. M9300~M9307= EC3X0~EC3X7;
M9310~M9317=EC3Y0~EC3Y7.
Destination #1 for the timing sequence pulse generative instruction DUTY (FNC186).
Destination #2 for the timing sequence pulse generative instruction DUTY (FNC186).
Destination #3 for the timing sequence pulse generative instruction DUTY (FNC186).
Destination #4 for the timing sequence pulse generative instruction DUTY (FNC186).
Destination #5 for the timing sequence pulse generative instruction DUTY (FNC186).
○
M9350
○
Y0 axis's external interrupt trigger type. When M9350= “OFF”, the interrupt is triggered by a rising
edge; when M9350= “ON”, that is triggered by a falling edge.
○ ○
○
M9370
○
Y1 axis's external interrupt trigger type. When M9370= “OFF”, the interrupt is triggered by a rising
edge; when M9370= “ON”, that is triggered by a falling edge.
○ ○
VS1
VS1
VS2
VS2
VSM
VSM
VS3
VS3
○
○
○
○
○
○
○
○
○
○
Y0 Axis's Positioning Control Flag
Y1 Axis's Positioning Control Flag
○
○
○
○
M9345
M9346
M9365
M9366
○
○
○
○
○
○
○
○
○
○
○
○
○
○
■
M9340
■
M9360
■
M9341
■
M9361
■
M9342
■
M9343
■
M9344
■
M9362
■
M9363
■
M9364
○ ○
○
○
○
○
○
○
○
○
○
○
○ ○
○
○
○
○
○
○
○
○
○
○
○ ○
○ ○
○
○
○
M9367
■
M9368
M9369
○
○
○
○
○
○
M9347
■
M9348
M9349
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Y0 axis's status. “OFF” means the Y0 is in the READY status, it is available for a positioning
instruction; while “ON” = BUSY, the Y0 has been occupying.
Y0 axis's pulse output monitor. “ON” means pulse is generating.
Y0 axis's positioning completed ag.
Y0 axis's positioning abnormal stop ag.
Y0 axis's zero home positioning has been completed.
Y0 axis's stop ag (with gradually slow down).
Y0 axis's immediately stop ag.
Y0 axis's table positioning start signal.
Y0 axis's M-code active ag.
Y0 axis's M-code clear command.
Y1 axis's status. “OFF” means the Y1 is in the READY status, it is available for a positioning
instruction; while “ON” = BUSY, the Y1 has been occupying.
Y1 axis's pulse output monitor. “ON” means pulse is generating.
Y1 axis's positioning completed ag.
Y1 axis's positioning abnormal stop ag.
Y1 axis's zero home positioning has been completed.
Y1 axis's stop ag (with gradually slow down).
Y1 axis's immediately stop ag.
Y1 axis's table positioning start signal.
Y1 axis's M-code active ag.
Y1 axis's M-code clear command.
Description
Relay ID
No.
Series
To Next Page
Loading...
Need help?
General