ABB ACS880 - Page 213

Def / Type
FbEq 16b / 32b
DescriptionName / Range /
Selection
No.
10 = 1 s / 100 = 1 sActivation delay for RO1.0.00 ... 3000.00 s
0.00 s / real32
(Visible when 14.1 Module 1 type = FDIO-01)
Defines the deactivation delay for relay output RO1. See
parameter 14.35 RO1 ON delay.
RO1 OFF delay14.36
10 = 1 s / 100 = 1 sDeactivation delay for RO1.0.00 ... 3000.00 s
100.000 / real32
(Visible when 14.1 Module 1 type = FAIO-01)
Defines the real value that corresponds to the maximum
analog input AI1 value defined by parameter 14.34 AI1
max.
See the drawing at parameter 14.35 AI1 scaled at AI1 min.
AI1 scaled at AI1 max14.36
1 = 1 / 1000 = 1Real value corresponding to maximum AI1 value.-32768.000 ...
32767.000
0.00 s / real32
(Visible when 14.1 Module 1 type = FIO-01)
Defines the deactivation delay for relay output RO1. See
parameter 14.35 RO1 ON delay.
RO1 OFF delay14.36
10 = 1 s / 100 = 1 sDeactivation delay for RO1.0.00 ... 3000.00 s
Not energized / uint32
(Visible when 14.1 Module 1 type = FDIO-01)
Selects a drive signal to be connected to relay output RO2.
For the available selections, see parameter 14.11 DIO1
output source.
RO2 source14.37
Not energized / uint32
(Visible when 14.1 Module 1 type = FIO-01)
Selects a drive signal to be connected to relay output RO2.
For the available selections, see parameter 14.11 DIO1
output source.
RO2 source14.37
0.00 s / real32
(Visible when 14.1 Module 1 type = FDIO-01)
Defines the activation delay for relay output RO2. See
parameter 14.35 RO1 ON delay.
RO2 ON delay14.38
10 = 1 s / 100 = 1 sActivation delay for RO2.0.00 ... 3000.00 s
0.00 s / real32
(Visible when 14.1 Module 1 type = FIO-01)
Defines the activation delay for relay output RO2. See
parameter 14.35 RO1 ON delay.
RO2 ON delay14.38
10 = 1 s / 100 = 1 sActivation delay for RO2.0.00 ... 3000.00 s
0.00 s / real32
(Visible when 14.1 Module 1 type = FDIO-01)
Defines the deactivation delay for relay output RO2. See
parameter 14.35 RO1 ON delay.
RO2 OFF delay14.39
10 = 1 s / 100 = 1 sDeactivation delay for RO2.0.00 ... 3000.00 s
0.00 s / real32
(Visible when 14.1 Module 1 type = FIO-01)
Defines the deactivation delay for relay output RO2. See
parameter 14.35 RO1 ON delay.
RO2 OFF delay14.39
10 = 1 s / 100 = 1 sDeactivation delay for RO2.0.00 ... 3000.00 s
- / real32
(Visible when 14.1 Module 1 type = FAIO-01)
Displays the value of analog input AI2 in mA or V
(depending on whether the input is set to current or
voltage).
This parameter is read-only.
AI2 actual value14.41
1000 = 1 mA or V /
1000 = 1 mA or V
Value of analog input AI2.-22.000 ... 22.000 mA
or V
Parameters 213