BEAMEX MC6 - Part 3, Meter; METER

To Next Page

To Previous Page

Things discussed in this part:

 Presenting the Meter and

how to take it into use.

Part 3

METER

Main Page

Default Chapter3
- Table of Contents3
Part 1, Introduction9
General10
- About this Manual10
  - Where am I10
  - Typographical Conventions11
- Unpacking and Inspection11
About MC612
- Starting MC612
- Firmware13
- Hardware15
- PC Communication / Calibration Software20
Options Software Options21
- Hardware Modules/Options and Accessories22
- Related Products22
Part 2, Active Terminals and Connections23
General24
Measurements Pressure Measurement25
- Connecting and Disconnecting External Pressure Modules25
- Zeroing a Pressure Module25
- Current Measurement26
- Voltage Measurement26
- Temperature Measurement (Thermocouple)27
- Temperature Measurement (RTD)27
- Resistance Measurement28
- Frequency Measurement28
- Temperature Measurement (RTD)28
- Pulse Counting29
- Switch Sensing29
  - Using the Soft Numeric Keypad30
Generations/Simulations Changing the Generated/Simulated Value31
- Spinning31
- Current Generation (Source or Sink)32
- Voltage Generation32
- Thermocouple Simulation33
- RTD Sensor Simulation33
- Resistance Simulation34
- Frequency Generation34
- Pulse Generation35
Thermocouple Connections36
Part 3, Meter37
About Meter38
Part 4, Calibrator39
About Calibrator40
Tools41
- General41
Part 5, Documenting Calibrator43
General44
- Calibration Software44
Calibrating Instruments45
- Generating/Simulating the Input Value45
- Instrument List46
- Instrument Overview Window49
- Calibrating an Instrument Using MC649
  - Changing the Pressure Module During Calibration51
  - About Fieldbus and HART Device Specifics52
Group Calibration53
- Collecting Instruments/Functions for Group Calibration53
  - Editing a Group54
- Calibrating a Group54
  - Group Settings55
  - Performing the Calibration55
Calibration Results56
- Deleting Calibration Results56
Digital Communication and Mc6'S Instrument Data57
- Getting and Editing Mapped Data57
Part 6, Data Logger61
General62
- Doing a Data Log63
Doing a Data Log Configuring63
- Saving and Opening Configurations63
- Starting the Data Log64
- Viewing and Saving or Deleting the Results65
- Viewing Saved Data Log Results65
- Transferring Data Log Results to a Personal Computer66
Part 7, Communicator67
General Warnings69
Connections70
- Selecting the Instrument71
Selecting the Instrument List of Found Devices71
About Instrument Parameters72
- Instrument Parameters in General72
- Calibrating or Data Logging HART Instruments73
- Calibrating or Data Logging Fieldbus Instruments73
- Editing Parameters74
- Trimming a Fieldbus Instrument75
- Trimming Ahart Instrument76
- HART Device Description Specifics77
HART Device Description Specifics General77
- Basic View78
- Managing Smart Transmitter Configurations79
Managing Smart Transmitter Configurations General79
- Tools in MC679
  - Saving Configurations79
  - Viewing/Managing Configurations80
- Beamex MC6 Fieldbus Configuration Viewer80
  - Uploading Configurations80
  - Linking Configurations to CMX80
Part 8, Settings82
Settings82
- Security Plus83
Security Plus General83
- Security Plus in Documenting Calibrator84
Additional Information86
- User Defined Pressure Units87
- User Defined PRT / RTD Sensors88
- User Defined Transfer Functions92
- User Defined Steps / Calibration Points93
- Controller Communication94
Appendix98
Appendix Safety98
- Approvals98
- Symbols Used98
- Safety Precautions and Warnings99
Disposal of Waste Electrical and Electronic Equipment104
- Beamex and WEEE104
  - Disposal of Battery Pack104
Service105
- Sending MC6 for Service105
- Firmware Update105
- Resetting MC6105
- The Battery Charger106
- Recalibrating MC6106
- Cleaning MC6106
- Statements107
Statements Disclaimer107
- Intellectual Property Rights108
  - Copyright108
  - Trademarks108
Index109

BEAMEX MC6 - Part 3, Meter; METER

Table of Contents

Other manuals for BEAMEX MC6

Related product manuals