106 S850 Operation & Maintenance Manual
SERVICE SCHEDULE
Chart
Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The
service schedule is a guide for correct maintenance of the Bobcat loader.
[1] Check every 8 - 10 hours for the first 24 hours, then at 50 hour intervals.
[2] Perform at first 50 hours, then as scheduled.
[3] Change oil and filter every 100 hours when operating under severe conditions.
[4] Or every 12 months.
SS SSL LF EXLF T3 MF EXMF iT4-0315
SERVICE SCHEDULE HOURS
ITEM SERVICE REQUIRED
8-10 50 100
[4]
250
[4]
500
[4]
1000
Engine Oil Check the oil level and add as needed. Do not overfill.
Engine Air Filter and Air System
Check display panel. Service only when required. Check for leaks and
damaged components.
Engine Cooling System
Clean debris from oil cooler, radiator and grille. Check coolant level COLD
and add premixed coolant as needed.
Fuel Filter Remove the trapped water.
Lift Arms, Lift Links, Cylinders,
Bob-Tach, Pivot Pins, Wedges
Lubricate with multipurpose lithium based grease.
Tires
Check for damaged tires and correct air pressure. Inflate to MAXIMUM
pressure shown on the sidewall of the tire.
Seat Bar, Control Interlocks,
Seat Belt, Seat Belt Retractors
Check the condition of seat belt. Clean or replace seat belt retractors as
needed. Check the seat bar and control interlocks for correct operation.
Clean dirt and debris from moving parts.
Bobcat Interlock Control
Systems (BICS™)
Check for correct function. Lift and Tilt functions MUST NOT operate with
seat bar raised. See details in this Manual.
Front Horn / Back-up Alarm Check for proper function.
Safety Signs and Safety Treads
Check for damaged signs (decals) and safety treads. Replace any signs or
safety treads that are damaged or worn.
Operator Cab Check the fastening bolts, washers and nuts. Check the condition of the cab.
Indicators and Lights Check for correct operation of all indicators and lights.
Heater and Air Conditioning
Filters (If Equipped)
Clean or replace filters as needed.
Hydraulic Fluid Check fluid level and add as needed.
Hydraulic Hoses and Tubelines Check for damage and leaks. Repair or replace as needed.
Final Drive Transmission
(Chaincase)
Check fluid level and add as needed.
Parking Brake, Foot Pedals and
Steering Handles or Joysticks
Check for correct operation. Repair or adjust as needed.
Wheel Nuts
Check for loose wheel nuts and tighten to correct torque. (See TIRE
MAINTENANCE in this manual.)
[1]
Spark Arrester Muffler Clean the spark chamber.
Battery
Check cables, connections and electrolyte level. Add distilled water as
needed.
Fuel Filter Replace filter element.
Engine / Hydrostatic Drive Belt Check for wear or damage. Check idler arm stop. [2]
Drive Belts (Alternator, air
conditioning, water pump)
Check condition. Replace as needed.
Bobcat Interlock Control
System (BICS™)
Check the function of the lift arm bypass control.
Engine Oil and Filter Replace oil and filter. [2] [3]
Hydraulic Charge Filter,
Hydraulic Reservoir Breather
Replace the charge filter and the reservoir breather.
Heater Coil and Air
Conditioning Evaporator (if
equipped)
Clean the heater coil and air conditioning evaporator. Clean the plenum
drains.
Hydraulic / Hydrostatic Filter Replace the hydraulic / hydrostatic filter.
Final Drive Transmission
(Chaincase)
Replace the fluid.
Hydraulic Reservoir Replace the fluid.
Engine Valves Adjust the engine valves.
Coolant Replace the coolant Every 2 years
WARNING
Instructions are necessary before operating or servicing machine. Read and
understand the Operation & Maintenance Manual, Operator’s Handbook and
signs (decals) on machine. Follow warnings and instructions in the manuals
when making repairs, adjustments or servicing. Check for correct function
after adjustments, repairs or service. Untrained operators and failure to follow
instructions can cause injury or death.
W-2003-0807
Dealer Copy -- Not for Resale
To Next Page