Cessna 182 1978 - Page 159

MODEL
182
& T182
SERIES
SERVICE
MANUAL
NOTE
5-25.
REASSEMBLY
OF McCAULEY
MAIN
WHEEL
AND
TIRE
ASSEMBLY.)
(Two-Piece
Wheel.)
Bearing cups
(races) (27)
are a press
fit in
a. Assemble
bearing
cone (5), grease
seal
retainer
wheel
halves (6),
and should
not be removed
(4), grease
seal felt
(3), grease
seal retainer
(2) and
unless
a new part is to be installed.
To re-
retaining ring
(1) into each wheel
half (6).
move
bearing cups,
heat wheel
half in
boiling
b.
Insert tube
in tire, aligning
index
marks on tire
water for
30 minutes,
or in an oven,
not to
and tube.
excees
121°C
(250°F).
Using
an arbor
press,
c. Place
wheel
half (6)
into tire
and tube
(side
if available, press out
bearing cup and press opposite valve
stem), aligning base of valve stem
in a
new bearing
cup while
wheel
half is still
in
valve slot.
With
washer (25)
under
head of thru-
hot.
bolt (24),
insert bolt through
wheel half
(6).
d.
Place
wheel
half
(6) into
other
side
of
tire
and
5-24. INSPECTION AND REPAIR OF
McCAULEY tube, aligning valve
stem in valve slot.
WHEEL
AND TIRE
ASSEMBLY.
(Two-Piece
Wheel.)
e.
Insert washers
(9) and
nuts (10) on
thru-bolts
a. Clean all metal parts and grease
seal felts in (24), and pre-torque
to 10-15 lb. in.
Stoddard
solvent
or
equivalent,
and
dry
thoroughly.
NOTE
Uneven
or
improper
torque
of the
nuts
A
soft bristle
brush
may
be
used to
remove
can
cause
failure
of the
bolts
with re-
hardened
grease,
dust
or dirt.
sultant
wheel
failure.
b.
Inspect
wheel
halves
(6)
for
cracks
or
damage.
f. Prior
to
torquing
nuts
(10),
inflate
tube
with
c.
Inspect
bearing
cones
(5),
cups
(27),
retaining
approximately
10-15
psi
air pressure
to seat
tire.
rings
(1),
grease
seal
retainers
(2),
grease
seal
felts
(3) and grease seal
retainers (4) for
wear or.
damage.
d.
Inspect
thru-bolts
(24)
and
nuts
(10)
for
cracks
in threads
or cracks
in radius
under
bolt head.
e. Replace
cracked
or
damaged
wheel
half
(6).
e.
Replace
cracked or
damaged
wheel
half (6).
h. Inflate
tire
to correct
pressure
specified
in
f.
Replace damaged
retainer rings (1)
and seals
figure 1-1 of
this manual.
(2),
(3)
and
(4).
g.
Replace
worn
or
damaged
bearing
cups
(27)
and
5-26.
INSTALLATION
OF
MAIN
WHEEL
cones
(5).
a.
Place
wheel
assembly
on
axle.
h.
Replace
any
worn
or
cracked
thru-bolts
(24) or
b. Install
axle
nut and
tighten
axle
nut until
a
slight
nuts
(10).
bearing
drag
is obvious
when
the
wheel
is
rotated.
i. Inspect
brake
discs
in
accordance
with
proce-
Back
off
axle
nut to nearest
castellation
and install
dures outlined
in paragraph
5-95.
cotter
pin.
j.
Remove
any
corrosion
or small
nicks.
c.
Place
brake back
plate
in position
and
secure
k. Repair reworked
areas of wheel by cleaning
with bolts and washers.
thoroughly,
then applying
one
coat of
clear lacquer
d. Install
speed
fairing
as outlined
in paragraph
paint.
5-13.
1. Pack bearings
with grease specified in Section 2
e. Remove jack and jack pad.
of
this manual.
SHOP NOTES:
Revision
1
5-9