Delta MH300 Series

To Next Page

To Previous Page

Chapter 14 Fault CodesMH300

14-38

Improper parameter settings for

speed tracking function

(including restart at momentary

power loss and restart after

fault)

Correct the parameter settings for speed tracking.

1. Start the speed tracking function.

2. Adjust the maximum current for Pr.07-09 speed tracking.

Main Page

Table of Contents4
Chapter 1 Introduction10
- 1-1 Nameplate Information11
- 1-2 Model Name12
- 1-3 Serial Number12
- 1-4 Apply After Service by Mobile Device13
- 1-5 RFI Jumper14
Chapter 2 Dimensions20
- 2-1 Frame A21
- 2-2 Frame B22
- 2-3 Frame C23
- 2-4 Frame D24
- 2-5 Frame E25
- 2-6 Frame F26
- 2-7 Frame G27
- 2-8 Frame H28
- 2-9 Frame I29
- 2-10 Digital Keypad30
Chapter 3 Installation32
- 3-1 Mounting Clearance33
- 3-2 Airflow and Power Dissipation34
Chapter 4 Wiring36
- 4-1 System Wiring Diagram38
- 4-2 Wiring39
Chapter 5 Main Circuit Terminals42
- 5-1 Main Circuit Diagram45
- 5-2 Main Circuit Terminals46
Chapter 6 Control Terminals58
- 6-1 Control Terminal Specifications61
Chapter 7 Optional Accessories66
- 7-1 All Brake Resistors and Brake Units Used in AC Motor Drives67
- 7-2 Magnetic Contactor / Air Circuit Breaker and Non-Fuse Circuit Breaker71
- 7-3 Fuse Specification Chart75
- 7-4 AC / DC Reactors78
- 7-5 Zero Phase Reactors108
- 7-6 EMC Filter111
- 7-7 EMC Shield Plate119
- 7-8 Capacitive Filter124
- 7-9 The Assembly of NEMA KIT126
- 7-10 The Assembly of Fan Kit139
- 7-11 Keypad Panel Mounting143
- 7-12 DIN-Rail Mounting144
- 7-13 Mounting Adapter Plate146
- 7-14 Digital Keypad – KPC-CC01150
Chapter 8 Option Cards190
- 8-1 Option Card Installation191
- 8-2 EMM-PG01L -- PG Card (Line Driver)202
- 8-3 EMM-PG01O -- PG Card (Open Collector)205
- 8-4 EMM-PG01R -- PG Card (Resolver / Encoder Signal Input)208
- 8-5 EMM-D33A -- Extension for 3-point Digital Input / 3-point Digital Output211
- 8-6 EMM-A22A -- Extension for 2 Sets of Analog Input / 2 Sets of Analog Output212
- 8-7 EMM-R2CA -- Relay Output Extension (2-point N.C. Output Terminal)213
- 8-8 EMM-R3AA -- Relay Output Extension (3-point N.O. Output Terminal)214
- 8-9 EMM-BPS02 -- +24V Power Extension Card215
- 8-10 CMM-DN02 -- Communication Extension Card, DeviceNet217
- 8-11 CMM-EIP02 -- Communication Extension Card, (Single-port) EtherNet/IP, Modbus-TCP220
- 8-12 CMM-EIP03 -- Communication Extension Card, (Dual-port) EtherNet/IP, Modbus-TCP224
- 8-13 CMM-PD02 -- Communication Extension Card, Profibus DP228
- 8-14 CMM-EC02 -- Communication Extension Card, EtherCAT230
- 8-15 Delta Standard Fieldbus Cables233
Chapter 9 Specification234
- 9-1 115V Models235
- 9-2 230V Models236
- 9-3 460V Models239
- 9-4 General Specifications241
- 9-5 Environment for Operation, Storage and Transportation242
- 9-6 Derating for Ambient Temperature and Altitude243
Chapter 10 Digital Keypad250
- 10-1 KPMH-LC01 Keyboard251
- 10-2 Descriptions of Keypad Functions251
- 10-3 Keypad Operation Process252
- 10-4 Reference Table for the 16-segment Digital Keypad LED Display258
Chapter 11 Summary of Parameter Settings260
- 00 Drive Parameters261
- 01 Basic Parameters269
- 02 Digital Input / Output Parameters274
- 03 Analog Input / Output Parameters280
- 04 Multi-step Speed Parameters284
- 05 Motor Parameters285
- 06 Protection Parameters (1)289
- 07 Special Parameters296
- 08 High-function PID Parameters299
- 09 Communication Parameters302
- 10 Speed Feedback Control Parameters307
- 11 Advanced Parameters310
- 12 Tension Control Parameters314
- 13 Macro (User-defined)319
- 14 Protection Parameters (2)320
Chapter 12 Descriptions of Parameter Settings326
- 12-1 Descriptions of Parameter Settings327
- 12-2 Adjustment & Application620
Chapter 13 Warning Codes650
Chapter 14 Fault Codes728
Chapter 15 CANopen Overview830
- 15-1 CANopen Overview832
- 15-2 Wiring for CANopen836
- 15-3 CANopen Communication Interface Descriptions837
- 15-4 CANopen Supporting Index849
- 15-5 CANopen Fault Codes857
- 15-6 CANopen LED Function862
Chapter 16 PLC Function Applications864
- 16-1 PLC Summary865
- 16-2 Notes Before Using a PLC866
- 16-3 Turn On868
- 16-4 Basic Principles of PLC Ladder Diagrams879
- 16-5 Various PLC Device Functions891
- 16-6 Introduction to the Command Window903
- 16-7 Display and Treatment of PLC Related Faults and Codes977
- 16-8 Explanation of Each PLC Mode Control (Speed, Torque)978
- 16-9 Count Function Using Pulse Input981
- 16-10 CANopen Master Control Applications982
- 16-11 Modbus Remote IO Control Applications (Use MODRW)993
Chapter 17 Safe Torque Off Function1000
- 17-1 Basic Function Description1001
- 17-2 Safe Torque Off Terminal Function Description1002
- 17-3 Wiring Diagram1003
- 17-4 Failure Rate of the Drive Safety Function1004
- 17-5 Reset the Parameter Settings1004
- 17-6 Timing Diagram Description1005
- 17-7 Fault Codes and Troubleshooting Instructions1008
- 17-8 Test and Fault Confirmation1010
Appendix A. Modbus Protocol1012
- A-1 Code Description1013
- A-2 Data Format1013
- A-3 Communication Protocol1015
- A-4 Address List1020
- A-5 Exception Response1027
Appendix B. Revision History1029

Delta MH300 Series - Page 765

Table of Contents

Related product manuals