Fluke 6105A - Energy Command Summary

6100B/6105A
Users Manual
5-26
Keyword Parameter Form Notes
:DIP
:TIME(?) <cpd> {SEConds|CYCLes}
:FLICker
:CURRent(?) <cpd> {HZ | CPM}
:VOLTage(?) <cpd> {HZ | CPM}
5-47. Energy Command Summary
Keyword Parameter Form Notes
[:SOURce]
:ENERgy
:MODE(?) <cpd>{ TCOunt | PACKet | GATE | FRUN }
:ABORt
:WUP:DURation(?) <cpd>{ SEConds | PPERiods | WH },<dnpd> The <dnpd> is the duration in
the selected units
:WUP:PSOurce(?) <cpd>{CH1 | CH2 | CH3 | CH4 | CH5 | CH6 |
SUM456 | MEAN456 | MEAN56 | EMUT | MAIN}
:TEST:DURation(?) <cpd>{ SEConds | PPERiods | WH },<dnpd> The <dnpd> is the duration in
the selected units
:TEST:PSOurce(?) <cpd>{CH1 | CH2 | CH3 | CH4 | CH5 | CH6 |
SUM456 | MEAN456 | MEAN56 | EMUT | MAIN}
:OGATe(?) <bool>{ OFF | ON | 0 | 1 },<cpd>{ PULSe | LEVel },
<cpd>{ HIGH | LOW },<cpd>{ R150 | R1000 }
:IGATe(?) <cpd>{ PULSe | LEVel },<cpd>{ HIGH | LOW },
<cpd>{ R150 | R1000 }
:MVOLtage(?) <cpd>{TCOunt | PACKet | GATE}[,<bool> {OFF |
ON | 0 | 1}]
<cpd> also required parameter
in query form of command
(specifies mode to query)
:UNIT(?) <cpd>{ REAL | APParent | REACtive }
:MUT:SOURce(?) <cpd>{ CH1 | CH1TO2 | CH1TO3 | CH1TO4 |
CH1TO5 | CH1TO6 }
:MUT:DEBounce[:STATe](?) <bool>{ OFF | ON | 0 | 1 }
:MUT:CONStant(?) <dnpd> in 'impulses per unit'
:MUT:CONStant:UNIT(?) {IPWH|IPKWH| IPMWH|WHPI|KWHPI|MWHPI}
:MUT:PULLup(?) <cpd>{ R150 | R1000 }
:REFerence:SOURce(?) <cpd>{ CH6 |SUM456 | MEAN456 | MEAN56 |
MMUT | MAIN }
:MUT:DEBounce[:STATe](?) <bool>{ OFF | ON | 0 | 1 }
:REFerence:CONStant(?) <dnpd> in 'impulses per unit'
:REFerence:CONStant:UNIT(?) {IPWH|IPKWH| IPMWH|WHPI|KWHPI|MWHPI}
:REFerence:PULLup(?) <cpd>{ R150 | R1000 }
:OUTput:CONStant(?) <dnpd> in 'impulses per unit'
:OUTPut:CONStant:UNIT(?) {IPWH|IPKWH| IPMWH|WHPI|KWHPI|MWHPI}
:OUTput:PULLup[:STATe](?) <bool>{ OFF | ON | 0 | 1}
:RESults? <cpd>{ CH1 | CH2 | CH3 | CH4 | CH5 | CH6 } Response =
<dnpd>, power or frequency.
<dnpd>, MUT Energy or
counts.
<dnpd>, Ref. Energy or
counts.
<dnpd> % Error or %
Registration.
Note: Interpretation of above
depends on setting of
ENERgy:PRESentation.
:PRESentation(?) <cpd>{ COUNts | ENERgy },<cpd>{ PERRor |
PREGistration }