Fujitsu ScanSnap N1800 User Manual

457
■ Action
When connecting using the scanner name, the connection will be an intranet connection. When
connecting using an IP address, it will be an internet connection. If the URL includes a scanner
name, the scanner will be connected using an Intranet Zone. If the URL includes an IP address,
the scanner will be connected using the Internet Zone.
Try the following settings for the corresponding zone.
1. In Internet Explorer, set the following settings in the [Tools] menu, [Internet Options].
2. Enable active scripting in either of the following ways.
z On the [Security] tab, click the [Default level] button to set [Security level for this zone] to
[Medium].
z On the [Security] tab, click the [Custom level] button to set to [Enable] for [Active scripting]
under [Scripting] in the [Settings] area.
3. If connecting via the Internet zone, on the [Privacy] tab, set the level to below [Medium High].
4. Delete temporary internet files in either of the following ways:
z For Internet Explorer 6.0
On the [General] tab, press the [Delete Files] button on the [Temporary Internet Files].
z For Internet Explorer 7.0
On the [General] tab, press the [Delete] button on the [Browsing history], and press [Delete
Files] button on [Temporary Internet Files].
z For Internet Explorer 8.0
On the [General] tab, press the [Delete] button on the [Browsing history], then select the
[Temporary Internet Files] check box and press [Delete] button.
■ Action
Press the power button to start the scanner.
■ Action
Set the proxy server to not be used.
1. In Internet Explorer, set the following settings in the [Tools] menu, [Internet Options].
2. Press the [LAN settings] button on the [Connections] tab.
3. Clear the [Use a proxy server for your LAN (These settings will not apply to dial-up or VPN
connection).] check box.
■ Action
Check if SSL is enabled on the [Admin Connection] window.
For details, refer to
"4.8.8 Setting the Admin Connection" (page 123).
In Internet Explorer, the security level for the target zone is set to [High]
on the [Security] tab in the [Tools] menu -[Internet Options].
In the case of a custom level, [Prompt] or [Disable] is set for [Active
scripting] under [Scripting] in the [Settings] area.
The scanner is in standby mode.
A proxy server is being used.
There is an error with the connection protocol setting.
There is an error with the port number setting.

Fujitsu ScanSnap N1800 Specifications

General

Film scanning	No
Color scanning	Yes
Input color depth	- bit
Maximum scan size	216 x 356 mm
Output color depth	24 bit
ADF scan speed (color, A4)	20 ppm
Optical scanning resolution	600 x 600 DPI
Duplex ADF scan speed (color, A4)	20 ipm
Display	TFT
Scanner type	ADF scanner
Product color	Black, Grey
Display diagonal	8.4 \
Display resolution	1024 x 768 pixels
Scan to	E-mail, Fax, File, FTP, Image
Sensor type	CCD
Scan file formats	JPG, PDF, TIFF
Maximum duty cycle	12000 pages per month
Daily duty cycle (max)	2000 pages
Minimum scan area (ADF)	50.8 x 50.8 mm
ISO A-series sizes (A0...A9)	A4, A5, A6, A7, A8
Maximum ISO A-series paper size	A4
Auto Document Feeder (ADF) media weight	52 - 127 g/m²
Auto document feeder (ADF) input capacity	50 sheets
Safety	LDAP, LDAPS, FTPS, HTTPS
Cabling technology	10BASE-T, 100BASE-TX
Networking features	Fast Ethernet
Supported network protocols	TCP/IP, DHCP, SMTP, SMB, LDAP, NTP, FTP, HTTP
Input voltage	100-240 V
Power supply type	AC
Power consumption (off)	0.5 W
Power consumption (standby)	15 W
Power consumption (typical)	50 W
Sustainability certificates	ENERGY STAR
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
Certification	RoHS

Weight and Dimensions

Depth	226 mm
Width	300 mm
Height	172 mm
Weight	6000 g