7.1 Temperature Controller/Servo/Inverter Connection 7-7
PG (Program)
PLC_CTL
Macro command “PLC_CTL F0 F1 F2”
Address Denotations
Name
Decimal
Place
Command
Address (BIN) Parameter 1 (BCD) Parameter 2 (BCD) Read Write
00 Pattern No. 0 Start SV 4
1, 3 3, 1
01 Pattern No. 0 SV/PV start -
1, 3 3, 1
04 Pattern No. Step No. Program setting SV 4
1, 3 3, 2
05 Pattern No. Step No. Program setting time 2
1, 3 3, 2
06 Pattern No. Step No. Step repeat times -
1, 3
-
07 Pattern No. Step No. PID No. -
1, 3 3, 4
08 Pattern No. Step No. ALM No. -
1, 3 3, 4
09 Pattern No. Step No. OPL No. -
1, 3 3, 4
0a Pattern No. Step No. OSL No. -
1, 3 3, 4
0b Pattern No. Step No.Sensor offset No. -
1, 3 3, 4
0c Pattern No. Step No.
Actual temperature
compensation No.
-
1, 3 3, 4
0d Pattern No. Step No. Wait time No. -
1, 3 3, 4
0e Pattern No. Step No. TS1 -
1, 3 3, 4
0f Pattern No. Step No. TS2 -
1, 3 3, 4
10 Pattern No. Step No. TS3 -
1, 3 3, 4
11 Pattern No. Step No. TS4 -
1, 3 3, 4
12 Pattern No. Step No. TS5 -
1, 3 3, 4
13 Pattern No. Step No. TS6 -
1, 3 3, 4
14 Pattern No. Step No. TS7 -
1, 3 3, 4
15 Pattern No. Step No. TS8 -
1, 3 3, 4
16 Pattern No. Step No. TS9 -
1, 3 3, 4
17 Pattern No. Step No. TS10 -
1, 3 3, 4
1a Pattern No. Step No. Link target pattern No. -
1, 3 3, 3
1b Pattern No. Step No. Output at 1st end -
1, 3 3, 3
1c Pattern No. Step No. Output at 2nd end -
1, 3 3, 3
1f 0 0 Pattern repeat times -
1, 3 3, 6
22 Pattern No. 0 Set number of steps -
1, 5
-
23 Pattern No. 0 Remaining number of steps -
1, 5
-
Contents F0 F1 (= $u n) F2
Alarm reset
1 - 8
(PLC1 - 8)
n Station number
2
n + 1 Command: 0000H
Pattern select
1 - 8
(PLC1 - 8)
n Station number
3n + 1 Command: 0001H
n + 2 Pattern No.
Step repeat
1 - 8
(PLC1 - 8)
n Station number
6
n + 1 Command: 0002H
n + 2 Pattern No.
n + 3 Start step
n + 4 End step
n + 5
Repeat times
Reset: 0000H
Times: 0001H to 0099H
Pattern copy
1 - 8
(PLC1 - 8)
n Station number
4
n + 1 Command: 0003H
n + 2 Copy source pattern No.
n + 3 Copy target pattern No.
Pattern clear
1 - 8
(PLC1 - 8)
n Station number
3
n + 1 Command: 0004H
n + 2
Pattern No.
Clear all patterns: 0000H
Clear individual pattern: 0001H to 0030H
To Next Page
Loading...
