HP MSR Router Series User Manual

229
Symptom 2: Ping failure
The remote end cannot be pinged after the modem is connected.
Solution
To resolve the problem:
1. Use the debugging ppp all command to verify that the same link layer encapsulation is used at the
two ends and correct PPP parameters are configured for authentication.
2. Verify that a correct IP address is assigned to the dialup interface.
3. Verify that DDR is enabled on the dialup interface.
4. Verify that the correct dialer-group and dialer-group rule commands are configured and
associated to make sure the packets can pass.
5. Use the debugging dialer event and debugging dialer packet commands to locate the problem.

HP MSR Router Series Specifications

General

Product Series	MSR
Category	Network Router
IPv6 Support	Yes
WAN Interfaces	Varies by model (e.g., Gigabit Ethernet, Serial, T1/E1)
LAN Interfaces	Varies by model (e.g., Fast Ethernet, Gigabit Ethernet)
VPN Support	Yes (IPSec, L2TP, GRE)
QoS Support	Yes (Priority queuing, traffic shaping)
Redundancy	Varies by model (e.g., VRRP, dual power supplies)
Management	CLI, Web GUI, SNMP
Firewall	Yes (Stateful firewall, NAT)

Summary

Configuring PPP and MP

PPP authentication

Details on supported PPP authentication methods: PAP, CHAP, MS-CHAP, and MS-CHAP-V2.

PPP for IPv4

PPP for IPv6

Configuring PPP

Tasks for configuring PPP, including encapsulation, authentication, negotiation, and compression.

Configuring MP

Tasks for configuring Multilink PPP (MP) using VT or MP-group interfaces.

PPP and MP configuration examples

Practical examples for configuring PPP and MP, including authentication and IP address negotiation.

Configuring PPPoE

Configuring the PPPoE server

Configuration tasks for setting up the PPPoE server.

Configuring a PPPoE client

Configuration tasks for setting up the PPPoE client.

PPPoE configuration examples

Practical examples for configuring PPPoE server and client scenarios.

Configuring L2TP

L2TP configuration task list

Configuring basic L2TP capabilities

Basic L2TP capability configuration, including enabling L2TP and creating L2TP groups.

Configuring an LAC

Tasks for configuring an LAC to initiate tunneling requests and specify LNS IP addresses.

Configuring an LNS

Tasks for configuring an LNS to accept tunneling requests and manage VA interfaces.

L2TP configuration examples

Practical examples for configuring L2TP tunnels (NAS, client, LAC-auto-initiated).

Troubleshooting L2TP

Configuring HDLC

Enabling HDLC encapsulation on an interface

Steps to enable HDLC encapsulation on an interface.

HDLC configuration example

Configuring HDLC link bundling

Configuring an HDLC link bundle interface

Steps to configure an HDLC link bundle interface.

Assigning an interface to an HDLC link bundle

Procedure for assigning interfaces to an HDLC link bundle.

HDLC link bundling configuration example

Configuring ISDN

ISDN configuration task list

Setting the ISDN switch type on an ISDN interface

Procedure to set the ISDN switch type on an interface.

Setting the ISDN functionality of an ISDN interface

Procedure to configure the ISDN interface as user-side or network-side.

Configuring Q.931 negotiation parameters

Configuring Q.931 call control parameters

Configuring the Q.921 operating parameters

Configuring the sliding window size on an ISDN BRI interface

ISDN configuration examples

Configuring ATM

ATM configuration task list

Configuring an ATM interface

Procedure to configure ATM interfaces.

Configuring a PVC

Procedure to configure a Permanent Virtual Circuit (PVC).

Configuring PPPoA

Procedure to enable PVC/PVC-group to carry PPP and configure PPPoA mapping.

Configuring PPPoEoA

Procedure to enable PVC/PVC-group to carry PPPoE and configure PPPoEoA mapping.

Configuring VP policing

ATM configuration examples