Kikusui TOS3200 - Panel Control Basics

To Next Page

To Previous Page

Panel Control Basics

This chapter explains how to select items on the screen and

how to enter values.

Main Page

Default Chapter2
- Use of Operation Manual2
- Safety Symbols3
- Notations Used in this Manual3
- Safety Precautions4
  - Measurement Category5
  - Table of Contents6
- Contents6
- Contents by Objectives12
- Front Panel14
- Rear Panel16
General Description17
- Product Overview18
  - Features18
- Options20
Installation and Preparation23
- Checking the Package Contents24
- Precautions Concerning Installation Location25
  - Using the Stand26
- Precautions for Moving the Product26
- Connecting the Power Cord27
  - Connecting the Power Cord for the TOS320028
  - Connecting the Power Cord for the EUT28
- Turning the Power on29
  - Turning the POWER Switch on29
  - Turning the POWER Switch off30
Panel Control Basics31
- Screen Configuration32
- Panel Control34
- Selecting the Operation Mode37
  - Single Tests (TC/PCC/METER)37
  - Program Tests (AUTO)37
- Panel Memory38
  - Storing to the Test Conditions39
  - Recalling from the Test Conditions39
TC and PCC Tests41
- Connecting the EUT42
- Judgment System50
  - Validity of the Lower Reference50
  - Test Wait Time and Judgment51
- Setting Test Conditions of the TC Measurement52
- Setting Test Conditions of the PCC Measurement56
- Setting Additional Test Conditions60
- Starting the Test62
- Stopping the Test66
- Storing the Test Results67
- Displaying the Test Results68
  - Deleting the Stored Data68
Meter Mode Measurement69
- Connecting the EUT70
  - Constructing the Connection Circuit70
  - Connecting the Test Lead (TL21-TOS)71
- Measuring in Meter Mode72
Program Test75
- Program Tests76
  - Limitations on the Test Conditions in the Steps77
  - Interval Time77
- Creating Sequence Programs78
- Sequence Program Editing Procedure83
- Setting Additional Test Conditions86
- Starting the Test88
  - When a Test Starts88
  - Unable to Start the Test90
- Stopping the Test91
- Storing the Test Results93
- Displaying the Test Results94
  - Deleting the Stored Data94
External Control95
- SIGNAL I/O Connector96
- Starting the Test99
- Recalling the Panel Memory and Sequence Program100
Remote Control101
- Remote Control Overview102
  - VISA Library103
- Using the RS232C Interface104
- Using the GPIB Interface107
- Using the USB Interface109
- Overview of Messages110
  - SCPI Command Syntax110
  - Parameters112
- Command Description in this Manual114
- IEEE488.2 Common Commands115
- Selecting the Operation Mode118
- Setting the TC Measurement and PCC Measurement118
- Executing the Test (Trigger Function)126
- Saving and Querying the Test Result130
- Setting the Program Test133
- Setting the Meter Mode Measurement138
- Querying the Measured Value140
- Various Settings144
- Status Register and Status Report Function150
- IEEE488.2 Register Model152
  - Status Byte Register152
  - Event Status Register153
- SCPI Register Model154
- Tutorial158
Maintenance161
- Test Lead Check162
- Measurement Check162
- Time Settings and Calibration Management164
  - Calibration165
- Replacing the Fuse166
- Replacing the Backup Battery166
Specifications167
- Measurement Items, Measurement Mode, and Measurement Network168
- Current Measurement Section*1168
- Judgment Function170
- Voltage Measurement between a and B171
- Timer, Test Function, and Memory171
- Other Functions172
- Interface173
- General174
- Outline Drawing175
- Measurement Network (NTWK)176
A Glossary177
Appendix177
B Four Principal Tests for Evaluating the Safety of Electrical and177
- Withstanding Voltage Test181
- Insulation Resistance Test182
- Earth Continuity Test183
- Leakage Current Test184
C a List of Messages186
D a List of Errors192
- Command Errors192
- Execution Errors193
- Query Errors194
E Processing Time of Main195
- Commands195
A List of Default Settings196
- Initializing the TOS3200196
- Default Values of the Panel Memory198
G System Settings200
- Setup Items of SYSTEM1/5200
- Setup Items of SYSTEM2/5201
- Setup Items of SYSTEM3/5202
- Setup Items of SYSTEM4/5202
- Setup Items of SYSTEM5/5203
H Protection Function204
Troubleshooting205

Kikusui TOS3200 - Panel Control Basics

Table of Contents

Other manuals for Kikusui TOS3200

Related product manuals