Kikusui TOS3200 - TC and PCC Tests

To Next Page

To Previous Page

TC and PCC Tests

This chapter explains the procedures from setting the test con-

ditions to saving the test results for the touch current and pro-

tective conductor current measurement tests.

Main Page

Default Chapter2
- Use of Operation Manual2
- Safety Symbols3
- Notations Used in this Manual3
- Safety Precautions4
  - Measurement Category5
  - Table of Contents6
- Contents6
- Contents by Objectives12
- Front Panel14
- Rear Panel16
General Description17
- Product Overview18
  - Features18
- Options20
Installation and Preparation23
- Checking the Package Contents24
- Precautions Concerning Installation Location25
  - Using the Stand26
- Precautions for Moving the Product26
- Connecting the Power Cord27
  - Connecting the Power Cord for the TOS320028
  - Connecting the Power Cord for the EUT28
- Turning the Power on29
  - Turning the POWER Switch on29
  - Turning the POWER Switch off30
Panel Control Basics31
- Screen Configuration32
- Panel Control34
- Selecting the Operation Mode37
  - Single Tests (TC/PCC/METER)37
  - Program Tests (AUTO)37
- Panel Memory38
  - Storing to the Test Conditions39
  - Recalling from the Test Conditions39
TC and PCC Tests41
- Connecting the EUT42
- Judgment System50
  - Validity of the Lower Reference50
  - Test Wait Time and Judgment51
- Setting Test Conditions of the TC Measurement52
- Setting Test Conditions of the PCC Measurement56
- Setting Additional Test Conditions60
- Starting the Test62
- Stopping the Test66
- Storing the Test Results67
- Displaying the Test Results68
  - Deleting the Stored Data68
Meter Mode Measurement69
- Connecting the EUT70
  - Constructing the Connection Circuit70
  - Connecting the Test Lead (TL21-TOS)71
- Measuring in Meter Mode72
Program Test75
- Program Tests76
  - Limitations on the Test Conditions in the Steps77
  - Interval Time77
- Creating Sequence Programs78
- Sequence Program Editing Procedure83
- Setting Additional Test Conditions86
- Starting the Test88
  - When a Test Starts88
  - Unable to Start the Test90
- Stopping the Test91
- Storing the Test Results93
- Displaying the Test Results94
  - Deleting the Stored Data94
External Control95
- SIGNAL I/O Connector96
- Starting the Test99
- Recalling the Panel Memory and Sequence Program100
Remote Control101
- Remote Control Overview102
  - VISA Library103
- Using the RS232C Interface104
- Using the GPIB Interface107
- Using the USB Interface109
- Overview of Messages110
  - SCPI Command Syntax110
  - Parameters112
- Command Description in this Manual114
- IEEE488.2 Common Commands115
- Selecting the Operation Mode118
- Setting the TC Measurement and PCC Measurement118
- Executing the Test (Trigger Function)126
- Saving and Querying the Test Result130
- Setting the Program Test133
- Setting the Meter Mode Measurement138
- Querying the Measured Value140
- Various Settings144
- Status Register and Status Report Function150
- IEEE488.2 Register Model152
  - Status Byte Register152
  - Event Status Register153
- SCPI Register Model154
- Tutorial158
Maintenance161
- Test Lead Check162
- Measurement Check162
- Time Settings and Calibration Management164
  - Calibration165
- Replacing the Fuse166
- Replacing the Backup Battery166
Specifications167
- Measurement Items, Measurement Mode, and Measurement Network168
- Current Measurement Section*1168
- Judgment Function170
- Voltage Measurement between a and B171
- Timer, Test Function, and Memory171
- Other Functions172
- Interface173
- General174
- Outline Drawing175
- Measurement Network (NTWK)176
A Glossary177
Appendix177
B Four Principal Tests for Evaluating the Safety of Electrical and177
- Withstanding Voltage Test181
- Insulation Resistance Test182
- Earth Continuity Test183
- Leakage Current Test184
C a List of Messages186
D a List of Errors192
- Command Errors192
- Execution Errors193
- Query Errors194
E Processing Time of Main195
- Commands195
A List of Default Settings196
- Initializing the TOS3200196
- Default Values of the Panel Memory198
G System Settings200
- Setup Items of SYSTEM1/5200
- Setup Items of SYSTEM2/5201
- Setup Items of SYSTEM3/5202
- Setup Items of SYSTEM4/5202
- Setup Items of SYSTEM5/5203
H Protection Function204
Troubleshooting205

Kikusui TOS3200 - TC and PCC Tests

Table of Contents

Other manuals for Kikusui TOS3200

Related product manuals