Lust CDA3000 - Page 351

Application Manual CDA3000
Appendix D Index
A-35
1
2
3
4
5
6
A
DE
EN
FR
Selection of user data sets via terminals ... 3-5,
5-15
Setting F1 MOP function
.................. 5-101
Switchover by terminal operation
.......... 5-15
Table sets (ASTER = ROT_3)
....... 4-34, 4-36
Table sets (ASTER=DRV_5)
................. 4-22
Terminal preset, ASTER=DRV_2
........... 4-12
Terminal preset, ASTER=DRV_3
........... 4-15
two directions (ASTER=M-S_1)
............ 4-54
two directions (ASTER=ROT_1)
............ 4-29
two directions (ASTER=ROT_2)
............ 4-31
Example of switchover via terminals
............. 3-5
Exponential representation on the KP200 display
....
3-12
Exponential value as
............................. 3-12
Exponential value display
........................ 3-12
F
Factory setting ............................. 5-2, 5-58
Factory setting of all user data sets
............. 2-18
Factory setting, data set
......................... 2-18
Factory setting, Definition
........................ 5-2
Fault current monitoring
......................... 5-89
Field bus operation
.............................. 4-40
Field bus operation, comparison of parameters 4-47
Field-Oriented Regulation (FOR)
................. 6-47
Fixed frequencies
.............................. 5-107
Fixed frequency selection
....................... 4-36
Fixed frequency, quick jog/slow jog
.......... 5-107
Frequency limitation
............................. 5-53
Frequency limits
................................. 5-53
Frequency ranges of the holding brake
......... 5-96
Function block
Adaptation of analog inputs
................. 5-17
Adaptation of analog output
................ 5-23
Adaptation of digital inputs
................. 5-27
Adaptation of digital outputs
................ 5-34
Control location selector
.................... 5-49
Functional areas
Characteristic data set parameters
....... 5-112
Functions in FOR, active
......................... 6-48
Functions in FOR, inactive
....................... 6-47
Functions in SFC, active
......................... 6-31
Functions in SFC, inactive
....................... 6-30
Functions in the preset, active
.................. 4-26
Functions of the DriveManager
.................. 3-13
Functions, active
......................... 4-25, 4-39
Functions, active in field bus operation
. 4-48, 4-62
Functions, active in preset
.............. 4-41, 4-52
G
Generally applied functions in open-loop control
mode VFC
..................................... 6-7
Glossary
............................................ 23
H
H1 flash code .................................... B-20
Hexadecimal representation of warning messages
..
5-84
How to use this manual
........................... 0-1
HTL output circuit, block diagram
............... 4-18
HTL output configuration block diagram
........ 6-50
Hysteresis
........................................ 5-83
Hysteresis of warning messages
................ 5-83
I
Increase standstill torque ...................... 5-134
Increase starting torque
....................... 5-134
Indication of whether a parameter is editable
... 3-7
Information for auto-tuning
...................... 6-31
Initial commissioning
............................. 5-4
Initial frequency
................................ 5-127
Input of motor data
............................... 5-6
Inputs
analog
....................................... 5-17
digital
........................................ 5-27
Specification
.................................. 2-9
Inputs and outputs
............................... 5-17
Intended use
...................................... 1-2
Interconnection on LustBus
..................... 5-91
Isolation concept
................................. 2-15
IxR load compensation
........................... 6-13
IxR load compensation block diagram
.......... 6-13
Ixt monitoring
.................................... 5-56
K
KeyPad ........................................... 5-71
KeyPad KP200
................................... 5-50
KeyPad KP200, operation
......................... 3-9