IMPULSE
®
•G+ & VG+ Series 4 Technical Manual
November 2020
Page 240
L04-05 Ref Loss Sel 0 0, 1 - Page 170
L04-06 Fref at Floss 80.0 0.0–100.0 % Page 170
L04-07 Freq Detect Sel 0 0, 1 - Page 170
L05-01 Test Mode 0 0, 1 - Page 171
L06-01 Torq Det 1 Sel 0 0–8 - Page 171
L06-02 Torq Det 1 Lvl 150 0–300 % Page 172
L06-03 Torq Det 1 Time 0.1 0.0–10.0 sec Page 172
L06-04 Torq Det 2 Sel 0 0–8 - Page 172
L06-05 Torq Det 2 Lvl 150 0–300 % Page 173
L06-06 Torq Det 2 Time 0.1 0.0–10.0 sec Page 173
L06-08 Mech Fatigue Sel 0 0–8 - Page 173
L06-09 MechFat Det Spd 110.0 -110.0–110.0 % Page 174
L06-10 MechFat Det Time 0.1 0.0–10.0 sec Page 174
L06-11 MechFat Det Hour 0 0–65535 - Page 174
L08-02 OH Pre-Alarm Lvl ** 50–150 °C Page 175
L08-03 OH Pre-Alarm Sel 3 0–5 - Page 175
L08-05 Ph Loss In Sel 1 0, 1 - Page 175
L08-07 Ph Loss Out Sel 1 0–2 - Page 175
L08-09 Ground Fault Sel 1 0, 1 - Page 175
L08-10 Fan On/Off Sel 1 0, 1 - Page 175
L08-11 Fan Delay Time 60 0–300 sec Page 175
L08-12 Ambient Temp 40 -10–50 °C Page 175
L08-13 UV3 Detect 1 0, 1 - Page 175
L08-15 OL2 Sel @ L-Spd 0 0, 1 - Page 175
L08-18 Soft CLA Sel 0 0, 1 - Page 175
L08-19 Fc Red dur OHAlm 0.8 0.1–0.9 Hz Page 175
L08-32 MC,FAN Fault Sel 1 0–4 - Page 175
L08-35 Installation Sel ** 0–3 - Page 175
L08-38 Fc Reduct dur OL 2** 0–2 - Page 175
L08-40 FC Reduct Time A01-02 0.00–2.00 sec Page 175
L08-41 High Cur Alm Sel 0 0, 1 - Page 176
L08-55 DB Tr protection 1 0, 1 - Page 176
L09-01 Reset Select 1 0, 1 - Page 177
L09-02 Reset Attempts 3 0–10 - Page 177
L09-03 Reset Time 0.5 0.5–600.0 sec Page 177
L09-04 Reset Latch Sel 1 0001 0000–FFFF - Page 177
L09-05 Reset Latch Sel 2 E000 0000–FFFF - Page 177
L09-06 Flt Contact Sel 0 0, 1 - Page 177
L09-07 Flt Latch Sel 1 0000 0000–FFFF - Page 179
L09-08 Flt Latch Sel 2 0000 0000–FFFF - Page 179
O01-01 User Monitor Sel 106 104–626 - Page 180
O01-02 Power-On Monitor 3 1–5 - Page 182
Parameter Parameter Name Default Range Units Reference
To Next Page
Loading...
Need help?
General
