4-83
4-2 Function Mode
4
Functions
*: Parameters changeable during operation.
• The 1st/2nd/3rd control functions are displayed identically. You'll see which one is enabled by checking whether
the terminal is turned on/off.
• When both SET and SET3 terminals are turned on, priority is given to SET, and the 2nd control function is
enabled.
• During operation, you cannot switch between the 1st, 2nd, and 3rd control functions. You can switch them only
during stop.
The functions switchable via the SET/SET3 terminal are:
F002/F202/F302 * : 1st/2nd/3rd acceleration time
F003/F203/F303 * : 1st/2nd/3rd deceleration time
A003/A203/A303 : 1st/2nd/3rd base frequency
A004/A204/A304 : 1st/2nd/3rd maximum frequency
A020/A220/A320 * : 1st/2nd/3rd multi-step speed reference 0
A041/A241 : 1st/2nd torque boost selection
A042/A242/A342 * : 1st/2nd/3rd manual torque boost voltage
A043/A243/A343 * : 1st/2nd/3rd manual torque boost frequency
A044/A244/A344 : 1st/2nd/3rd V/f characteristics selection
A046/A246 * : 1st/2nd automatic torque boost
voltage compensation gain
A047/A247 * : 1st/2nd automatic torque boost slip
compensation gain
A061/A261 * : 1st/2nd frequency upper limit
A062/A262 * : 1st/2nd frequency lower limit
A092/A292/A392 * : 1st/2nd/3rd acceleration time 2
A093/A293/A393 * : 1st/2nd/3rd deceleration time 2
A094/A294 : 1st/2nd 2-step acceleration/deceleration
selection
A095/A295 : 1st/2nd 2-step acceleration frequency
A096/A296 : 1st/2nd 2-step deceleration frequency
b012/b212/b312 * : 1st/2nd/3rd electronic thermal level
b013/b213/b313 * : 1st/2nd/3rd electronic thermal characteristics
selection
H002/H202 : 1st/2nd motor parameter selection
H003/H203 : 1st/2nd motor capacity selection
H004/H204 : 1st/2nd motor pole number selection
H005/H205 * : 1st/2nd speed response
H006/H206/H306 * : 1st/2nd/3rd stabilization parameter
H020/H220 : 1st/2nd motor parameter R1
H021/H221 : 1st/2nd motor parameter R2
H022/H222 : 1st/2nd motor parameter L
H023/H223 : 1st/2nd motor parameter I0
H024/H224 : 1st/2nd motor parameter J
H030/H230 : 1st/2nd motor parameter R1 (auto-tuning)
H031/H231 : 1st/2nd motor parameter R2 (auto-tuning)
H032/H232 : 1st/2nd motor parameter L (auto-tuning)
H033/H233 : 1st/2nd motor parameter I0 (auto-tuning)
H034/H234 : 1st/2nd motor parameter J (auto-tuning)
H050/H250 * : 1st/2nd PI proportional gain
H051/H251 * : 1st/2nd PI integral gain
H052/H252 * : 1st/2nd P proportional gain
H060/H260 * : 1st/2nd Limit at 0 Hz
Inverter
U/T1
V/T2
W/T3
SET
SET3
P24
Motor 1
Motor 2
Motor 3
To Next Page
Loading...
