Planmeca ProMax - Technical Manual

To Next Page

Planmeca ProMax

& Planmeca ProMax 3D / 3D s

10010812_31

technical manual

Main Page

Table of Contents3
Chapter a GENERAL & TECHNICAL DATA9
Warnings and Cautions9
Manual Versions10
Symbols on Product Labels10
Technical Specifications11
User's Statement13
Promax 3D: Ctdi Values20
Promax 3D: Stray Radiation Measurements23
X-Ray Units with 3D Sensor24
X-Ray Units with 3D S Sensor25
HANDLING PRECAUTIONS for Pcbs and SOFTWARE CHIPS27
Handling Printed Circuit Boards27
Handling Software Flash Memory Chips27
Emc Information28
Switching X-Ray Unit on32
Chapter B INFORMATION DISPLAYS33
General about Information Displays33
Contents of the Information Displays34
User Preference Settings35
Setting Date and Time35
Audio Settings37
Behavioural Preferences38
Visual Adjustments39
Select Language41
Default Program Settings42
Feature Program Control45
Enable / Disable Features45
Special Functions47
Special Operation Mode Selection47
Error History48
Exposure Statistics49
X-Ray Tube Head Seasoning49
Taking a Test Exposure50
Beam Check51
Network Settings51
Service Settings56
Special Operation Mode Selection57
Preheat Calibration58
Maximum Height58
Exposure Program Tuning59
Factory Default Settings60
Configuration Selftest61
Select Configuration61
Patient Support Alignment66
Software Update66
Technical Calibrations67
Collimator Speed Adjustment68
Height Adjustment Maximum Speed Setting69
QA Exposure69
DAP Value Adjustments70
Troubleshooting71
Dimax Communication72
Network Status73
Sensor Communication73
Entering the Password74
Chapter C HELP & ERROR MESSAGES75
Main Categories75
Help Messages76
Error Messages78
Motorized Motion Related Errors (2Xx78
X-Ray Generation Related Errors (3Xx81
Feedback Errors (4Xx84
Power Supply Related Errors (5Xx86
Communication Errors (6Xx86
Calibration Errors (7Xx88
System Conflicts (8Xx89
Infrastructure Errors (9Xx91
Chapter D PREVENTIVE MAINTENANCE93
System Maintenance93
Cleaning93
Operating Checks93
Preventive Maintenance Checks94
General94
X-Ray Tube Feedback System94
Mechanical Checks97
Column Motor Nut97
Chapter E C-ARM and IMAGING ARM99
Required Tools99
Panoramic Beam and Patient Positioning Mechanism Adjustment103
Adjustment Procedure104
Checking the Panoramic Beam Position105
Adjusting the Sensor Head Angle108
Primary Collimator Angle Adjustment110
Panoramic Beam Adjustment112
Patient Positioning Mechanism Adjustment117
Calibration of Angle Sensors129
Beam Check136
Taking a Ball Phantom Exposure137
Panoramic Mode Patient Positioning Lights139
Adjustment of Tomo Mode Patient Positioning Lights146
Calibrating Panoramic Sensor Head152
X-Ray Unit with Fixed Primary Collimator - Primary Collimator Adjustment153
Promax 3D: Adjustments & Calibrations157
Adjustment Procedure157
Checking the Connection between Pcs and X-Ray Unit159
Beam Adjustment160
Beam Check166
Flat Field Calibration166
Geometry Calibration166
Quality Assurance (Q/A) Test166
Other Adjustments and Calibrations167
Calibrating the Elbow Arm and C-Arm Gear Ratios167
Calibrating the Panoramic Dynamic Exposure Control (DEC169
Removing the Covers175
C-Arm Upper Covers175
Removing the Fixed Sensor Head Holder Covers176
Removing the Movable Sensor Head Holder Covers178
Removed by Pulling It from Its Position178
Connector178
C-Arm Inner Cover179
Figure 107179
Tube Head Covers180
Figure 108180
Shoulder Arm Covers182
Replacing the Sensor Head184
Attaching and Removing the Fixed Sensor Head184
Sensor Head with Quick Connector Mechanism188
Promax 3D: Replacing the Sensor Head191
REPLACING Pcbs194
C-Arm PCB194
Replacing Tube Head196
Promax 3D: Replacing Collimator197
Promax 3D: Updating Reconstruction Pc Software200
Promax 3D: Updating Sensor Software201
Chapter F PATIENT SUPPORT ARM203
Adjustments203
Patient Positioning Mechanism Adjustment203
Panoramic Mode Patient Positioning Lights203
Removing the Covers209
Patient Support Table Cover209
Support Arm Lower Cover210
Replacing the Gui Software212
GUI Software Update, Only for Colour GUI212
Replacing GUI Software Chip, Only for Black/White GUI213
Replacing Pcbs214
Patient Position Control PCB214
Graphic User Interface (GUI) PCB215
Chapter G COLUMN219
Adjustments219
Adjusting the Telescopic Column Position219
Calibrating the Column Motor Position Sensor222
Removing the Covers226
Removing the Telescopic Column Upper Front Panel226
Removing the Telescopic Column Rear Cover Plates228
Replacing the Column Motor229
Replacing the Motor229
Replacing the Lift Nut Assembly236
Replacing/Upgrading Software243
Replacing the CPU PCB Software Chips (Alternative 1243
Loading the Software from a Computer (Alternative 2245
Replacing the Battery on the Rtc Pcb247
Replacing Pcbs248
Power PCB248
ETHERNET PCB and CPU PCB253
Input PCB254
Chapter H CEPHALOSTAT257
Adjustments and Calibrations257
Required Tools257
Preparations before Adjustments259
Checking and Adjusting the Sensor Head and Second Primary Collimator Mutual Position260
Adjusting the Sensor and Second Primary Collimator Rails262
Adjusting the Sensor Head Connector and Sensor Head Positions263
Adjusting the Height of the Cephalostat267
Checking the Cephalostat Head Support Position270
Cephalostat Head Support Position Adjustment272
Calibrating the C-Arm Position275
Synchronizing the Scanning Mechanism and First Primary Collimator281
Adjusting the Cephalometric Beam Vertical Position283
Checking the Second Primary Collimator Position286
Adjusting the Second Primary Collimator Position289
Beam Check293
Calibrating the Cephalostat Sensor Head298
Calibrating the Cephalometric DEC305
Checking the Adjustment310
Removing and Attaching the Second Primary Collimator311
Attaching the Second Primary Collimator Covers312
Detaching and Attaching the Sensor Head313
Cephalostat with Movable Sensor Head313
Cephalostat with Fixed Sensor Head - Removing and Attaching the Sensor Head317
Removing the Housings and Covers320
Removing the Housings of the Head Support320
Replacing Pcbs323
Cephalostat Connector PCB323
Chapter I PLANMECA PROCEPH325
Adjustments and Calibrations325
Required Tools325
Removing the Necessary Covers326
Parameter Values and Beam Check Exposure326
Adjusting the Height of the Cephalostat330
Checking the Cephalostat Head Support Position332
Calibrating the Left Side of the Cephalometric X-Ray Beam334
Cephalostat Head Support Adjustments335
Adjusting the Cephalometric Beam Top Limit338
Calibrating the Right Side of the X-Ray Beam340
Checking the Adjustment341
Removing the Housings and Covers342
Removing the Housings of the Head Support342
Chapter J DIAGRAMS345

Planmeca ProMax - Technical Manual

Table of Contents

Other manuals for Planmeca ProMax

Related product manuals