R&S LCX Series - Index

Index
R&S
®
LCX Series
233User Manual 1179.2260.02 ─ 02
Index
A
Abort
Dynamic impedance measurement .......................... 101
About
Auto function ............................................................... 73
Binning ...................................................................... 103
Cable length ................................................................73
External bias ............................................................... 73
Measurement speed ................................................... 73
Open/Short/Load correction ........................................73
Source impedance ...................................................... 73
Test fixture .................................................................. 52
Test signal type ........................................................... 73
Access
Binning settings ................................................ 104, 105
Configuration preset ................................................... 83
CSV settings ............................................................. 122
Data and time settings ...................................... 124, 125
Device information .................................................... 129
Display mode settings .................................................69
Dynamic impedance measurement settings ............... 99
File manager settings ................................................ 113
FTP settings ......................................................154, 155
GPIB settings .................................................... 156, 157
Instrument ................................................................... 43
Interfaces .................................................................. 117
LAN settings ..................................................... 149, 151
Licenses settings ...................................................... 126
Live chart settings ....................................................... 87
Live chart viewer ......................................................... 86
Logging chart settings .................................................90
Logging chart viewer ...................................................89
Logging settings ..........................................................94
Measurement control functions ...................................72
Measurement mode settings ...................................... 67
Measurement parameters ...........................................75
Open/Short/Load correction parameters .................... 78
Save/Recall settings ................................................. 133
Screenshot ................................................................120
Sound settings .......................................................... 125
Specific instrument functions ...................................... 85
Test signal settings ..................................................... 71
Update device ........................................................... 131
User button ................................................................118
VNC settings ..................................................... 153, 154
Activating the locked touch input ..................................... 119
Active elements ................................................................. 41
Address
GPIB settings ............................................................ 157
Alphanumeric parameters ................................................. 46
APERTure
Commands ............................................................... 175
Appearance
Setup ........................................................................ 124
Application cards ............................................................... 15
Application notes ............................................................... 15
Apply configuration
Time .......................................................................... 153
Assign screenshot to user button .................................... 121
Assign touch lock to user button ......................................119
Auto
Measurement control functions ...................................73
Auto function
Measurement functions .............................................. 77
Purity angle ................................................................. 77
Serial/Parallel separation point ................................... 77
Axial lead type
Test fixture .................................................................. 52
B
Back
Live chart .................................................................... 88
Basic steps
Trying out .................................................................... 32
Beeper .............................................................................125
Bench top, placing the R&S LCX ...................................... 17
Bias
Configure .................................................................... 59
connector .................................................................... 31
External voltage .......................................................... 60
Fuse holder ................................................................. 31
Internal current ............................................................61
Internal voltage ........................................................... 59
BIAS
Commands ............................................................... 178
Bias current
How to: configure internal current bias ....................... 61
How to: deactivate internal current bias ......................62
Bias enable
Measurement functions .............................................. 72
Binning
About ........................................................................ 103
Bins ........................................................................... 107
Commands ............................................................... 198
connector .................................................................... 31
Counter ..................................................................... 107
Enable .......................................................................105
End of measurement bin ...........................................107
File ............................................................................ 107
Histogram ................................................................. 108
How to: Configure binning file ................................... 108
Indicator .................................................................... 107
Load from file ............................................................ 105
Out bin ...................................................................... 107
Pin assignment of interface ...................................... 104
Primary parameter characteristic .............................. 107
Secondary parameter characteristic ......................... 107
Settings ..................................................................... 104
Settings softkey ........................................................ 107
Specific functions ...................................................... 102
Binning measurement
Settings ..................................................................... 105
Bins
Binning ...................................................................... 107
BNC
Connectors ................................................................. 29
BNC-to-BNC extension
Test fixture .................................................................. 57
Brightness
Display .............................................................. 124, 125
Keys .................................................................. 124, 125
Setup ........................................................................ 125
Brochures .......................................................................... 15