R&S ZNA67 - Control Commands

Command reference
R&S
®
ZNA
1117User Manual 1178.6462.02 ─ 20
Setting parameters:
<OldTraceName> String parameter with old trace name, e.g. 'Trc1'
<NewTraceName> String parameter with new trace name, e.g. 'S11 Trace'
*RST: n/a
Example: See CONFigure:CHANnel<Ch>:TRACe:REName
Usage: Setting only
Manual operation: See "Table Area" on page 390
7.3.3 CONTrol commands
The Control... commands allow you to configure the following interfaces:
●
User Port
●
External Handler I/O (Universal Interface, option R&S ZNBT-Z14)
●
RFFE GPIO interface (option R&S ZNA-B15)
●
R&S VSE (see Chapter 4.7.6.1, "Live pulse analysis with R&S VSE", on page 251
CONTrol:AUXiliary:C[:DATA]..........................................................................................1118
CONTrol:GPIO<Port>:SENSe:VOLTage?........................................................................1119
CONTrol:GPIO<Port>:SENSe:CURRent?....................................................................... 1120
CONTrol:GPIO:SENSe:SUMCurrent?.............................................................................1120
CONTrol<Ch>:GPIO:SENSe:TRIGger............................................................................ 1121
CONTrol<Ch>:GPIO:TIME............................................................................................ 1121
CONTrol<Ch>:GPIO:VOLTage:OUTPut.......................................................................... 1121
CONTrol<Ch>:GPIO<Port>[:STATe]............................................................................... 1122
CONTrol<Ch>:GPIO<Port>:RANGe............................................................................... 1122
CONTrol<Ch>:GPIO<Port>:SHUNt?.............................................................................. 1123
CONTrol<Ch>:GPIO<Port>:VOLTage[:DEFault]...............................................................1124
CONTrol<Ch>:RFFE:TEST:OUTPut............................................................................... 1124
CONTrol<Ch>:RFFE:TEST:TIME................................................................................... 1124
CONTrol<Ch>:RFFE:TEST:SENSe:TRIGger...................................................................1125
CONTrol<Ch>:RFFE<Bus>:COMMand:DATA..................................................................1125
CONTrol<Ch>:RFFE<Bus>:COMMand:SEND.................................................................1125
CONTrol<Ch>:RFFE<Bus>:COMMand:SEND?...............................................................1125
CONTrol<Ch>:RFFE<Bus>:SETTings[:STATe]................................................................ 1126
CONTrol<Ch>:RFFE<Bus>:SETTings:FREQuency..........................................................1126
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:IO..........................................................1126
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:LOW......................................................1126
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:HIGH..................................................... 1126
CONTrol<Ch>:RFFE<Bus>:TEST:DATA......................................................................... 1127
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk.......................................................................1127
CONTrol<Ch>:RFFE<Bus>:TEST:VIO............................................................................1127
CONTrol<Ch>:RFFE<Bus>:TEST:DATA:RANGe............................................................. 1128
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk:RANGe...........................................................1128
CONTrol<Ch>:RFFE<Bus>:TEST:VIO:RANGe................................................................1128
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk:SHUNt?.......................................................... 1128
CONTrol<Ch>:RFFE<Bus>:TEST:DATA:SHUNt?.............................................................1128
SCPI command reference