Siemens simovert masterdrives Compendium

Function diagram
87654321
fp_mc_010_e.vsd
List of contents
MASTERDRIVES MC
05.04.06
Basic Functions
- 10 -
V2.5
MASTERDRIVES MC function diagram - List of contents of the basic functions
Contents Sheet
General
Basic functions: List of contents 10
Free blocks and extension boards: List of contents 12
Explanation of the symbols 15
Visualization and normalization parameters 20
Free display parameters 30
Operator control
PMU 50
OP1S operating display 60
MC terminals
Analog inputs/outputs 80
Digital inputs/outputs 90
Energizing main contactor, external DC 24 V supply 91
"Safe Stop" function 92
Communications
Receiving via USS/SCom1 100
Receiving via USS/SCom2 101
Transmitting via USS/SCom1 110
Transmitting via USS/SCom2 111
First CB/TB board, receiving 120
First CB/TB board, receiving 121
PROFIBUS CBP2, synchronizing 122
First CB/TB board, transmitting 125
Second CB/TB board, receiving 130
Second CB/TB board, receiving 131
Second CB/TB board, transmitting 135
SIMOLINK board: Configuration and diagnosis 140
SIMOLINK board: Synchronizing 141
SIMOLINK board 2: Configuration and diagnosis 145
SIMOLINK board: Receiving 150
SIMOLINK board: Transmitting 160
SIMOLINK board: Transmitting, special data 160a
Position setpoint extrapolation 170
Position setpoint extrapolator 171
Encoder interface DP V3 encoder 1 (motor enc.) 172a
Encoder interface DP V3 encoder 2 (external enc.) 172b
Control words and status words
Control word 1 180
Control word 2 190
Status word 1 200
Status word 2 210
Encoder evaluation
Resolver evaluation, motor encoder (slot C) 230
Encoder evaluation, motor encoder (slot C) 240
Encoder evaluation, external encoder (not slot C) 242
Pulse enc. evaluation, motor encoder (slot C) 250
Pulse enc. evaluation, ext. encoder (not slot C) 255
Setpoint input, ext. encoder with SBP 256
Multiturn enc. eval., motor encod. (slot C) 260
Multiturn enc. eval., external encoder (not slot C) 270
Setpoint channel
Fixed setpoints 290
Motorized potentiometer 300
Setpoint selection 310
Ramp-function generator 320
Position sensing and control
Position fixed values and fixed setp. on the DSP 325
Motor encoder with mechanical gearing 327
Position sensing for motor encoder (slot C) 330
Config. of position sensing for mot. enc. (slot C) 331
Start position of absolute encoder with mech. gear
ratio for technology encoder 333
Position sensing for external encoder 335
Config. of position sensing for ext. enc. (not slot C) 336
Position control 340
Speed controller / torque limitation
Speed controller 360
Speed controller with reference model 360a
Speed filter 361
Torque limitation 370
Current controller / V/f characteristic
Current controller synchronous motor 389
Current controller asynchronous motor 390
Current controller asynchronous motor (P296=3) 390a
Current controller motor parameters 391
Adaptation of torque constant in the case
of synchronous motors 393
Tr-Adaptation for asynchronous machines 394
Calculation of the acceleration torque 398
Friction characteristic 399
V/f characteristic 400
Gating unit / braking control
Gating unit 420
Braking control 470
Diagnostics
Messages 480
Protective functions, Part 1 490
Protective functions, Part 2 (motor) 491
Protective functions, Part 3 (blocking protection) 492
Protective functions, Part 4 (stall diagnosis V/f
characteristic (P290 = 1)) 493
Actual values 500
Actual speed values 500a
DC link voltage reduction 501
Fault memory 510
Hardware configuration Part 1 515
Hardware configuration Part 2 517
Status diagram 520
Functions
Data sets 540
"Calculation of motor model" function 550
Vdmax control 610
Harmonic compensation 630
Cyclic Load Compensation (CLC) 631
Contents Sheet Contents Sheet

Siemens simovert masterdrives Specifications

General

Brand	Siemens
Model	simovert masterdrives
Category	DC Drives
Language	English