434 Agilent InfiniiVision 3000 X-Series Oscilloscopes User's Guide
Index
BW Limit? in DVM display, 256
C
calibrate probe, 70
calibration, 306
calibration protect button, 44, 45
calibration status, 327
CAN decode, source channels, 352
CAN frame counter, 357
CAN serial decode, 355
CAN totalizer, 357
CAN trigger, 353
capture signal bursts, 199
cardiac waveform generator output, 262
Center, FFT, 83
channel labels, 137
channel, analog, 63
channel, bandwidth limit, 67
channel, coupling, 65
channel, invert, 68
channel, on/off keys, 41
channel, position, 65
channel, probe units, 69
channel, skew, 70
channel, vernier, 67
channel, vertical sensitivity, 65
characteristics, 331
chart logic bus state math function, 99
chart logic bus timing math function, 98
choosing values, 37
cleaning, 309
clear display, 196
clear display, Quick Clear Display, 311
clear persistence, 134
clock, 304
CMOS threshold, 113
common logarithm math function, 92
COMP license, 340
compensate passive probes, 34, 41
Config softkey, 297, 298
connect probes, digital, 105
connection, to a PC, 298
connectors, rear panel, 44
control, remote, 295
controls, front panel, 35
copyright, 2
Counter measurement, 230
counter, ARINC 429 words/errors, 420
counter, CAN frame, 357
counter, FlexRay frame, 373
counter, UART/RS232 frame, 430
coupling, channel, 65
coupling, trigger, 182
crosstalk problems, 83
CSV file format, 276
CSV files, minimum and maximum
values, 349
current probes, 337
cursor measurements, 205
cursor units, 208
Cursors key, 40
Cursors knob, 40
cursors, binary, 207
cursors, hex, 207
cursors, manual, 206
cursors, track waveform, 207
D
D*, 39, 113
d/dt math function, 79
damage, shipping, 25
data sheet, 331
DC channel coupling, 66
DC offset correction for integrate
waveform, 81
DC RMS - Full Screen measurement, 226
DC RMS - N Cycles measurement, 226
DC signals, checking, 181
DC waveform generator output, 261
dead time (re-arm), 202
decibels, FFT vertical units, 84
decimating samples, 193
decimation, for measurement record, 349
decimation, for screen, 349
default configuration, 31
default label library, 141
default setup, 31, 286
Default Setup key, 38
defaults, waveform generator, 274
delay knob, 51
Delay measurement, 218, 232
delay time indicator, 59
delayed sweep, 56
delete character, 283
delete file, 299
Demo 1 terminal, 41
Demo 2 terminal, 41
depth, AM modulation, 271
deviation, FM modulation, 272
DHCP, 297,
298
differential probes, 336
differentiate math function, 79
Digit softkey, 155
digital bus mode, 114
digital channel controls, 39
digital channel inputs, 42
digital channel menu, 112
digital channels, 112
digital channels, AutoScale, 109
digital channels, enabling, 341
digital channels, logic threshold, 112
digital channels, probing, 117
digital channels, size, 111
digital display, interpreting, 110
Digital key, 39
digital probes, 105, 117
digital probes, impedance, 117
digital voltmeter (DVM), 255
Display key, 40
display multiple acquisitions, 188
display, area, 47
display, interpreting, 46
display, persistence, 133
display, signal detail, 131
display, softkey labels, 47
display, status line, 47
displayed channels AutoScale, 303
distortion problems, 83
Divide math function, 77
DNS IP, 297
dual-channel (N2820A probe)
measurements, 219
Duty cycle measurement,
231
duty cycle measurement trend, 98
DVM (digital voltmeter, 255
DVM license, 340
Dynamic DNS, 297
E
ECL threshold, 113
edge speeds, 192
edge then edge triggering, 148
edge triggering, 146
EDK license, 340
To Next Page
Loading...
Need help?
General
