Cessna 182 1978 - Page 65

MODEL 182 &
T182 SERIES SERVICE
MANUAL
SPECIAL
EACH
EACH
EACH
INSPECTIONS
2-50. INSPECTION
TIME
LIMITS (Model
182 & T182
Airplanes)
50
100
200
HOURS.
HOURS
HOURS
HOURS
YEARS
J 36 Crankcase,
Oil Sump, and Accessory
Section - Inspect
for cracks
and evidence
of
oil leakage.
Check bolts
and
nuts
for looseness
and retorque
as
necessary.
Check
crankcase
breather lines
for obstructions,
security
and
general
condition.
K Fuel
System (Section
12)
K 1 Integral Fuel
Tanks - Check for
evidence of leakage
and •
O
condition
of
fuel caps,
adapters,
and placards.
K 2 Fuel Bladders
- Check for leaks
and security, condition
of •
O
fuel caps,
adapters and
placards.
K 3
Fuel System
- Inspect
plumbing
and
components
for
mounting
and
security.
K 4 Fuel Tank
or Bladder
Drains - Drain
water and sediment.
•
K
5 Fuel
Tank Vent
Lines
and Vent
Valves -
Check vents
for
Obstruction
and
proper
positioning.
K 6
Fuel Selector
Valve
- Check
controls
for detent
in each
position,
security
of attachment,
and for proper
placarding.
K 7
Fuel Strainer,
Drain
Valve,
and Controls
- Check
freedom
of movement,
security,
and proper
operation.
Disassemble,
flush and
clean screen
and bowel.
K
8
Fuel Quantity
Indicators
- Check
for damage
and
security
Each
of installation.
1
K
9 Fuel
quantity
indicating
system
operational
test is
required
Each
every
12 months.
Refer to
Section 15
for detailed
1
accomplishment
instructions.
L Propeller
and Propeller
Governor
(Section
13)
L 1
Proper Mounting
- Check
for security
of installation.
L 2 Propeller
Blades
- Inspect for
cracks, dents,
nicks,
scratches,
erosion,
corrosion,
or other
damage.
L
3 Spinner
- Check general
condition
and attachment.
L
4 Spinner
and
Spinner
Bulkhead
- Remove
spinner,
wash,
and
inspect for cracks
and fractures.
L
5 Propeller
Mounting
Bolts
- Inspect
mounting
bolts
and
safety-wire
for
signs of looseness.
Retorque mounting
bolts as required.
L
6 Propeller Hub -
Check general condition.
L
7 Propeller
Governor
and
Control
- Inspect
for oil
and •
p
grease leaks.
L 8 Propeller
Anti-ice
Slip
Rings,
Brushes
and Boots
- Inspect
.
for condition,
and
security. Perform
operational
check.
M
Utility
Systems
(Section
14)
M
1 Ventilation
System
- Inspect clamps,
hoses,
and valves
400
Each
for condition
and
security.
1
M 2
Heater Components,
Inlets,
and Outlets
- Inspect
all lines,
connections,
ducts,
clamps, seals
and gaskets
for
condition,
restriction,
and security.
M
3 Cabin Heat
and Ventilation
Controls
- Check freedom
of
movement
through full
travel. Check
friction
locks for
proper
operation.
M 4 Pitot
Tube and Stall
Warning Vane
- Check for
condition •
and
obstructions.
Temporary
Revision
Number
3
2-34
©
2002 Cessna
Aircraft
Company
7 October
2002