Cessna 182 1978 - Page 78

MODEL
182
& T182 SERIES
SERVICE
MANUAL
CESSNA
PROGRESSIVE
CARE
MODEL
182
& T182
OPERATION
NO.
1
Registration
No.
Airplane
Model and
SN _
Airplane Time
INSPECTION
COMPLETED
BY
J
3 Engine. Propeller
Controls,
and Linkage
- Check general
condition,
freedom
of
movement
through
full range.
Check
for
proper travel,
security
of attachment,
and for evidence
of wear.
Check
friction
locks for proper
operation.
J 4
Cowl Flap Controls
- Check
freedom of
movement through
full travel.
J
5 Ignition
Switch
and Electrical
Harness
- Inspect
for damage,
condition,
and
security.
J
6 Firewall
Structure
- Inspect
for wrinkles,
damage,
cracks.
sheared
rivets,
etc.
Check
cowl shock
mounts
for
condition
and security.
J
7
Engine Shock
Mounts,
Engine
Mount
Structure,
and
Ground Straps
- Check
condition, security,
and
alignment.
J 8 Induction
System
- Check security
of clamps,
tubes, and
ducting.
Inspect
for evidence
of
leakage.
J
9 Induction
Air Filter - Remove
and clean.
Inspect
for
damage, and
service per paragraph
2-24.
J 10
Induction Airbox,
Valves, Doors,
and Controls
- Remove
air
filter
and inspect
hinges. doors,
seals, and
attaching
parts
for
wear and
security.
Check
operation.
Clean
and
inspect
air filter
and re-oil if flock-coated.
J
11 Alternate
Induction
Air System -
Check for obstructions,
operation,
and security.
J
13 Alternator,
Mounting
Bracket, and
Electrical Connections
-
Check
condition
and
security.
Check
alternator
belts
for
condition
and
proper
adjustment.
Refer
to Paragraph
1642
for belt tension.
J
15 Oil Cooler
- Check for
obstructions,
leaks, and security
of
attachment.
J 16
Exhaust
System
- Inspect
for cracks
and security.Air
leak
check
exhaust system. Refer
to Section 11 and
11A,
Paragraphs
11-98
and 11-75A.
for
inspection
procedures
J 17
Exhaust System
(turbocharged
engine) -
Inspect couplings,
seals, clamps,
and
expansion joints
for cracks.
Air leak
check exhaust system.
J
18 Auxiliary
(Electric) Fuel
Pump - Check
pump and fittings
for
condition,
operation,
security.
Remove
and clean
filler (as
applicable).
J 19 Engine-Driven
Fuel Pump - Check for evidence
of leakage,
security of attachment,
and general
condition.
J 21 Magnetos
- Check
external
condition. security,
and
electrical
leads for condition.
Check
timing to
engine and
internal
timing if engine
timing requires adjustment.
J
23 Ignition
Harness and
Insulators - Check
for proper
routing.
deterioration,
and condition
of terminals.
J 24 Spark Plugs
- Remove, clean analyze,
test, gap. and rotate
top plugs-to-bottom
and bottom
plugs-to-top.
J
25 Cylinder
Compression
- Perform
differential compression
test
J
26 Carburetor
- Drain
and flush carburetor
bowl. clean
inlet
strainer, and
drain plug
Check
general condition
and
security.
J 27 Engine
Primer - Check
for leakage,
operation,
and security.
Revision 3 2-45