Chroma A620028 - Page 20

Programmable DC Power Supply (with Solar Array Simulation) 62000H Series
Operating & Programming Manual
xviii
3.3.3.5 Setting Parallel Parameters ................................................................... 3-32
3.3.3.6 Setting Procedure for APG in Series or Parallel ..................................... 3-34
3.3.4 DISPLAY ................................................................................................... 3-36
3.3.4.1 BRIGHTNESS ....................................................................................... 3-36
3.3.4.2 DISPLAY SELECTION .......................................................................... 3-37
3.3.4.3 READING AVERAGE TIMES ................................................................ 3-39
3.3.5 PROTECTION ........................................................................................... 3-40
3.3.5.1 OVP Protection ...................................................................................... 3-40
3.3.5.2 OCP Protection ..................................................................................... 3-41
3.3.5.3 OPP Protection ...................................................................................... 3-42
3.3.5.4 REMOTE INHIBIT ................................................................................. 3-43
3.3.5.5 SAFETY INT.LOCK ............................................................................... 3-45
3.3.5.6 EXTERNAL ON/OFF ............................................................................. 3-47
3.3.5.7 FOLDBACK ........................................................................................... 3-48
3.3.5.8 OTP ....................................................................................................... 3-50
3.3.5.9 AC FAULT ............................................................................................. 3-51
3.3.5.10 SENSE FAULT Protection ................................................................. 3-51
3.3.5.11 FANLOCK Protection......................................................................... 3-52
3.3.5.12 D/D FAULT Protection ....................................................................... 3-53
3.3.5.13 CURR. SHARING ERR Protection..................................................... 3-53
3.3.5.14 FPGA UPDATE! Protection ............................................................... 3-54
3.3.5.15 C/S CABLE ERR. Protection ............................................................. 3-55
3.3.5.16 MATCH Warning ............................................................................... 3-56
3.3.6 FACTORY SETTING ................................................................................. 3-56
3.3.7 CALIBRATION .......................................................................................... 3-57
3.3.7.1 Voltage Output & Measurement Calibration ........................................... 3-60
3.3.7.2 Current Measurement Calibration .......................................................... 3-62
3.3.7.3 Current Output (PROG.) Calibration ...................................................... 3-65
3.3.7.4 APG Voltage Calibration ........................................................................ 3-69
3.3.7.5 APG Current Calibration ........................................................................ 3-72
3.3.7.6 IV Voltage Output & Measurement Calibration (62020H-150S Only) ..... 3-74
3.3.7.7 IV Current Calibration (62020H-150S Only) ........................................... 3-77
3.3.8 REMOTE SETUP ...................................................................................... 3-80
3.3.8.1 GPIB ADDRESS ................................................................................... 3-80
3.3.8.2 ETHERNET ........................................................................................... 3-80
3.3.8.3 RS232/RS485 ....................................................................................... 3-82
3.3.8.4 BAUDRATE ........................................................................................... 3-83
3.3.8.5 RS485 ADDR ........................................................................................ 3-83
3.3.8.6 RS485 TERMINATOR ........................................................................... 3-84
3.3.8.7 RS485 PARSER .................................................................................... 3-84
3.3.9 OUTPUT MODE ........................................................................................ 3-85
3.3.9.1 CV/CC MODE ....................................................................................... 3-86
3.3.9.2 TABLE MODE ....................................................................................... 3-86
3.3.9.3 SAS MODE ........................................................................................... 3-88
3.3.9.4 EN50530 MODE .................................................................................... 3-92
3.3.9.5 SANDIA MODE ..................................................................................... 3-93
3.3.9.6 Error Message ....................................................................................... 3-95
4. Program Sequence ........................................................................................... 4-1
4.1 LIST MODE ........................................................................................................ 4-1
4.1.1 Description of PROGRAM Settings ............................................................. 4-2
4.1.1.1 Setting EXT._TRIG PULL ........................................................................ 4-3
4.1.1.2 Setting PROG NO. .................................................................................. 4-3
4.1.1.3 Setting RUN COUNT ............................................................................... 4-3