Chroma A620028 - Page 21

Programmable DC Power Supply (with Solar Array Simulation) 62000H Series
Operating & Programming Manual
xix
4.1.1.4 Setting PROG CHAIN .............................................................................. 4-5
4.1.1.5 Setting CLEAR PROGRAM ..................................................................... 4-8
4.1.2 Setting Sequence ........................................................................................ 4-9
4.1.2.1 Setting Sequence Number .................................................................... 4-10
4.1.2.2 Setting Sequence Type ......................................................................... 4-10
4.1.2.3 Setting Time .......................................................................................... 4-14
4.1.2.4 Setting Voltage ...................................................................................... 4-14
4.1.2.5 Setting Voltage Slew Rate ..................................................................... 4-14
4.1.2.6 Setting Current ...................................................................................... 4-14
4.1.2.7 Setting Current Slew Rate ..................................................................... 4-15
4.1.3 Execution in LIST MODE........................................................................... 4-15
4.1.3.1 Running LIST MODE ............................................................................. 4-15
4.1.3.2 Program List Mode Description ............................................................. 4-16
4.2 V_STEP MODE ................................................................................................ 4-16
4.2.1 Setting V_STEP MODE ............................................................................. 4-17
4.2.1.1 Setting START_VOLTAGE .................................................................... 4-17
4.2.1.2 Setting END_VOLTAGE ........................................................................ 4-18
4.2.1.3 Setting RUN_TIME ................................................................................ 4-18
4.2.2 Execution of V_STEP MODE .................................................................... 4-19
4.2.2.1 Running V_STEP MODE ....................................................................... 4-19
4.2.2.2 Description of Program V_Step Mode ................................................... 4-20
4.3 IV PROGRAM ................................................................................................... 4-20
4.3.1 Setting IV-PROGRAM ............................................................................... 4-21
4.3.2 Setting IV-Sequence ................................................................................. 4-22
4.3.2.1 Setting Sequence Number .................................................................... 4-22
4.3.2.2 Setting IV-FILE Number ........................................................................ 4-23
4.3.2.3 Setting Sequence Type ......................................................................... 4-23
4.3.2.4 Setting Time .......................................................................................... 4-24
4.3.3 Execution of IV PROGRAM ....................................................................... 4-25
4.3.3.1 Running IV PROGRAM ......................................................................... 4-25
4.3.3.2 IV Program Main Screen ....................................................................... 4-26
5. Remote Operation ............................................................................................ 5-1
5.1 Overview ............................................................................................................. 5-1
5.1.1 USB Interface .............................................................................................. 5-1
5.1.2 Setting GPIB, Ethernet, RS-232C & RS-485 Parameters ............................ 5-1
5.1.3 Connecting RS-232C .................................................................................. 5-1
5.1.4 Connecting RS-485 ..................................................................................... 5-2
5.1.5 Ethernet Remote Control ............................................................................. 5-3
5.1.5.1 Selecting the LAN to be Connected ......................................................... 5-4
5.1.5.2 Setting IP, Subnet Mask & Gateway ........................................................ 5-6
5.1.5.3 Confirming Network Connected Successfully ........................................ 5-11
5.1.5.4 Communicating with the Instrument ....................................................... 5-13
5.2 GPIB Function of 62000H Series ...................................................................... 5-19
5.3 Introduction to Programming ............................................................................. 5-19
5.3.1 Conventions .............................................................................................. 5-20
5.3.2 Numerical Data Formats............................................................................ 5-20
5.3.3 Boolean Data Format ................................................................................ 5-20
5.3.4 Character Data Format .............................................................................. 5-20
5.3.5 Basic Definition ......................................................................................... 5-21
5.3.5.1 Command Tree Structure ...................................................................... 5-21
5.3.5.2 Program Headers .................................................................................. 5-21
5.3.5.3 Common Command and Query Headers ............................................... 5-21
5.3.5.4 Instrument-Controlled Headers .............................................................. 5-21