Cisco Catalyst 3560-X User Manual

1-48
Catalyst 3750-X and 3560-X Switch Software Configuration Guide
OL-25303-03
Chapter 1 Configuring IP Unicast Routing
Configuring BGP
Table 1-9 Default BGP Configuration
Feature Default Setting
Aggregate address Disabled: None defined.
AS path access list None defined.
Auto summary Enabled.
Best path
• The router considers as-path in choosing a route and does not compare similar
routes from external BGP peers.
• Compare router ID: Disabled.
BGP community list
• Number: None defined. When you permit a value for the community number, the
list defaults to an implicit deny for everything else that has not been permitted.
• Format: Cisco default format (32-bit number).
BGP confederation identifier/peers
• Identifier: None configured.
• Peers: None identified.
BGP Fast external fallover Enabled.
BGP local preference 100. The range is 0 to 4294967295 with the higher value preferred.
BGP network None specified; no backdoor route advertised.
BGP route dampening Disabled by default. When enabled:
• Half-life is 15 minutes.
• Re-use is 750 (10-second increments).
• Suppress is 2000 (10-second increments).
• Max-suppress-time is 4 times half-life; 60 minutes.
BGP router ID The IP address of a loopback interface if one is configured or the highest IP address
configured for a physical interface on the router.
Default information originate
(protocol or network redistribution)
Disabled.
Default metric Built-in, automatic metric translations.
Distance
• External route administrative distance: 20 (acceptable values are from 1 to 255).
• Internal route administrative distance: 200 (acceptable values are from 1 to 255).
• Local route administrative distance: 200 (acceptable values are from 1 to 255).
Distribute list
• In (filter networks received in updates): Disabled.
• Out (suppress networks from being advertised in updates): Disabled.
Internal route redistribution Disabled.
IP prefix list None defined.
Multi exit discriminator (MED)
• Always compare: Disabled. Does not compare MEDs for paths from neighbors in
different autonomous systems.
• Best path compare: Disabled.
• MED missing as worst path: Disabled.
• Deterministic MED comparison is disabled.

Cisco Catalyst 3560-X Specifications

General

Enclosure Type	Rack-mountable - 1U
Subtype	Gigabit Ethernet
Ports	48 x 10/100/1000 + 4 x SFP
Flash Memory	64 MB
Power Device	Internal power supply
Voltage Required	AC 120/230 V (50/60 Hz)
Operating System	Cisco IOS
Device Type	Switch
Performance	Switching capacity: 128 Gbps
Jumbo Frame Support	Yes
Routing Protocol	RIP-1, RIP-2, EIGRP
Remote Management Protocol	SNMP 1, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, HTTP, HTTPS
Features	DHCP support, VLAN support, QoS, IPv6 support, Syslog
Compliant Standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad, IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ag, IEEE 802.3at
Stacking	Stackable
Security Features	SSH, RADIUS, TACACS+
Management	CLI
Dimensions (H x W x D)	17.5 in
Operating Temperature	32 to 113 °F (0 to 45 °C)
Humidity	10 - 95% (non-condensing)