EasyManuals Logo

Cisco Catalyst 3560-X User Manual

Cisco Catalyst 3560-X
1538 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #215 background imageLoading...
Page #215 background image
CHAPTER
1-1
Catalyst 3750-X and 3560-X Switch Software Configuration Guide
OL-25303-03
1
Configuring SDM Templates
This chapter describes how to configure the Switch Database Management (SDM) templates on the
Catalyst 3750-X or 3560-X switch. Unless otherwise noted, the term switch refers to a Catalyst 3750-X
or 3560-X standalone switch and to a Catalyst 3750-X switch stack.
Note For complete syntax and usage information for the commands used in this chapter, see the command
reference for this release.
This chapter consists of these sections:
Understanding the SDM Templates, page 1-1
Configuring the Switch SDM Template, page 1-5
Displaying the SDM Templates, page 1-7
Understanding the SDM Templates
You can use SDM templates to configure system resources in the switch to optimize support for specific
features, depending on how the switch is used in the network. You can select a template to provide
maximum system usage for some functions; for example, use the default template to balance resources,
and use the access template to obtain maximum ACL usage. The switch SDM templates allocate system
hardware resources for different uses.
You can select SDM templates for IP Version 4 (IPv4) to optimize these features on switches running
the IP Base or IP Services feature set:
Note When the switch is running the LAN Base feature set, do not select a routing template (sdm prefer
routing). The routing values shown in the templates are not valid on the switch. To configure IPv4 static
routing on switches running the LAN Base feature set, you must use the default template.
Routing—The routing template maximizes system resources for unicast routing, typically required
for a router or aggregator in the center of a network.
VLANs—The VLAN template disables routing and supports the maximum number of unicast MAC
addresses. It would typically be selected for a Layer 2 switch.
Default—The default template gives balance to all functions.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3560-X and is the answer not in the manual?

Cisco Catalyst 3560-X Specifications

General IconGeneral
Enclosure TypeRack-mountable - 1U
SubtypeGigabit Ethernet
Ports48 x 10/100/1000 + 4 x SFP
Flash Memory64 MB
Power DeviceInternal power supply
Voltage RequiredAC 120/230 V (50/60 Hz)
Operating SystemCisco IOS
Device TypeSwitch
PerformanceSwitching capacity: 128 Gbps
Jumbo Frame SupportYes
Routing ProtocolRIP-1, RIP-2, EIGRP
Remote Management ProtocolSNMP 1, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, HTTP, HTTPS
FeaturesDHCP support, VLAN support, QoS, IPv6 support, Syslog
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad, IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ag, IEEE 802.3at
StackingStackable
Security FeaturesSSH, RADIUS, TACACS+
ManagementCLI
Dimensions (H x W x D)17.5 in
Operating Temperature32 to 113 °F (0 to 45 °C)
Humidity10 - 95% (non-condensing)

Related product manuals