EasyManuals Logo

Cisco Catalyst 3560-X User Manual

Cisco Catalyst 3560-X
1538 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1314 background imageLoading...
Page #1314 background image
1-58
Catalyst 3750-X and 3560-X Switch Software Configuration Guide
OL-25303-03
Chapter 1 Configuring IP Multicast Routing
Configuring Advanced DVMRP Interoperability Features
Controlling Route Exchanges
These sections describe how to tune the Cisco device advertisements of DVMRP routes:
Limiting the Number of DVMRP Routes Advertised, page 1-58 (optional)
Changing the DVMRP Route Threshold, page 1-58 (optional)
Configuring a DVMRP Summary Address, page 1-59 (optional)
Disabling DVMRP Autosummarization, page 1-61 (optional)
Adding a Metric Offset to the DVMRP Route, page 1-62 (optional)
Limiting the Number of DVMRP Routes Advertised
By default, only 7000 DVMRP routes are advertised over an interface enabled to run DVMRP (that is,
a DVMRP tunnel, an interface where a DVMRP neighbor has been discovered, or an interface configured
to run the ip dvmrp unicast-routing interface configuration command).
Beginning in privileged EXEC mode, follow these steps to change the DVMRP route limit. This
procedure is optional.
To configure no route limit, use the no ip dvmrp route-limit global configuration command.
Changing the DVMRP Route Threshold
By default, 10,000 DVMRP routes can be received per interface within a 1-minute interval. When that
rate is exceeded, a syslog message is issued, warning that there might be a route surge occurring. The
warning is typically used to quickly detect when devices have been misconfigured to inject a large
number of routes into the MBONE.
Command Purpose
Step 1
configure terminal Enter global configuration mode.
Step 2
ip dvmrp route-limit count Change the number of DVMRP routes advertised over an interface
enabled for DVMRP.
This command prevents misconfigured ip dvmrp metric interface
configuration commands from causing massive route injection into the
MBONE.
By default, 7000 routes are advertised. The range is 0 to 4294967295.
Step 3
end Return to privileged EXEC mode.
Step 4
show running-config Verify your entries.
Step 5
copy running-config startup-config (Optional) Save your entries in the configuration file.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3560-X and is the answer not in the manual?

Cisco Catalyst 3560-X Specifications

General IconGeneral
Enclosure TypeRack-mountable - 1U
SubtypeGigabit Ethernet
Ports48 x 10/100/1000 + 4 x SFP
Flash Memory64 MB
Power DeviceInternal power supply
Voltage RequiredAC 120/230 V (50/60 Hz)
Operating SystemCisco IOS
Device TypeSwitch
PerformanceSwitching capacity: 128 Gbps
Jumbo Frame SupportYes
Routing ProtocolRIP-1, RIP-2, EIGRP
Remote Management ProtocolSNMP 1, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, HTTP, HTTPS
FeaturesDHCP support, VLAN support, QoS, IPv6 support, Syslog
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad, IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ag, IEEE 802.3at
StackingStackable
Security FeaturesSSH, RADIUS, TACACS+
ManagementCLI
Dimensions (H x W x D)17.5 in
Operating Temperature32 to 113 °F (0 to 45 °C)
Humidity10 - 95% (non-condensing)

Related product manuals