Cisco Catalyst 3560-X User Manual

1-11
Catalyst 3750-X and 3560-X Switch Software Configuration Guide
OL-25303-03
Chapter 1 Configuring SNMP
Configuring SNMP
Step 4
snmp-server user username groupname
{remote host [udp-port port]} {v1 [access
access-list] | v2c [access access-list] | v3
[encrypted] [access access-list] [auth {md5 |
sha} auth-password]} [priv {des | 3des | aes
{128 | 192 | 256}} priv-password]
Add a new user for an SNMP group.
• The username is the name of the user on the host that connects
to the agent.
• The groupname is the name of the group to which the user is
associated.
• Enter remote to specify a remote SNMP entity to which the
user belongs and the hostname or IP address of that entity with
the optional UDP port number. The default is 162.
• Enter the SNMP version number (v1, v2c, or v3). If you enter
v3, you have these additional options:
– encrypted specifies that the password appears in
encrypted format. This keyword is available only when
the v3 keyword is specified.
– auth is an authentication level setting session that can be
either the HMAC-MD5-96 (md5) or the HMAC-SHA-96
(sha) authentication level and requires a password string
auth-password (not to exceed 64 characters).
• If you enter v3 you can also configure a private (priv)
encryption algorithm and password string priv-password (not
to exceed 64 characters).
– priv specifies the User-based Security Model (USM).
– des specifies the use of the 56-bit DES algorithm.
– 3des specifies the use of the 168-bit DES algorithm.
– aes specifies the use of the DES algorithm. You must
select either 128-bit, 192-bit, or 256-bit encryption.
• (Optional) Enter access access-list with a string (not to exceed
64 characters) that is the name of the access list.
Step 5
end Return to privileged EXEC mode.
Step 6
show running-config Verify your entries.
Note To display SNMPv3 information about auth | noauth |
priv mode configuration, you must enter the show snmp
user EXEC command.
Step 7
copy running-config startup-config (Optional) Save your entries in the configuration file.
Command Purpose

Cisco Catalyst 3560-X Specifications

General

Enclosure Type	Rack-mountable - 1U
Subtype	Gigabit Ethernet
Ports	48 x 10/100/1000 + 4 x SFP
Flash Memory	64 MB
Power Device	Internal power supply
Voltage Required	AC 120/230 V (50/60 Hz)
Operating System	Cisco IOS
Device Type	Switch
Performance	Switching capacity: 128 Gbps
Jumbo Frame Support	Yes
Routing Protocol	RIP-1, RIP-2, EIGRP
Remote Management Protocol	SNMP 1, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, HTTP, HTTPS
Features	DHCP support, VLAN support, QoS, IPv6 support, Syslog
Compliant Standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad, IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ag, IEEE 802.3at
Stacking	Stackable
Security Features	SSH, RADIUS, TACACS+
Management	CLI
Dimensions (H x W x D)	17.5 in
Operating Temperature	32 to 113 °F (0 to 45 °C)
Humidity	10 - 95% (non-condensing)