Dynamic DX - Page 6

GBK60348
: Issue 1 – October 2007
6
5.3.10 System Settings parameters ........................................ 89
5.3.10.1 CLAM Slowdown............................................................. 89
5.3.10.2 Neutral to PB Delay......................................................... 90
5.3.10.3 Chair Speed Enable........................................................ 90
5.3.10.4 Single Profile Mode ......................................................... 91
5.3.10.5 CANH Power Switch........................................................ 91
5.3.10.6 CAN Terminator............................................................... 91
5.3.10.7 UCM Joystick Swap Left/Right....................................... 92
5.3.10.8 Rotate UCM Joystick....................................................... 92
5.3.10.9 ACU Enable...................................................................... 92
5.3.10.10 ACU Joystick Swap Left/Right ....................................... 93
5.3.10.11 ACU has Momentary Switch.......................................... 93
5.3.10.12 ACU Momentary Switch Timeout.................................. 93
5.3.10.13 RJM Enable....................................................................... 94
5.3.10.14 RJM Joystick Swap Left/Right........................................ 94
5.3.10.15 RJM has Analog Joystick................................................ 94
5.3.10.16 Joystick Switch Threshold ............................................... 96
6 DX Modules .............................................................97
6.1 Introduction.................................................................................... 97
6.1.1 The GPSB/SLIO ............................................................... 97
6.2 Secondary Remotes...................................................................... 98
6.2.1 Available Secondary Remotes................................... 98
6.3 DX Steering/Actuator/Lighting Modules.................................... 99
6.4 DX Environmental Control Modules..........................................100
6.5 DX Auxiliary Modules...................................................................100
6.6 Programmable parameters.......................................................101
6.6.1 Actuator Settings (CLAM/TAM)................................. 103
6.6.1.1 CLAM Enable................................................................. 103
6.6.1.2 CLAM is Critical.............................................................. 103
6.6.1.3 Actuator While Driving.................................................. 103
6.6.1.4 Actuator 1 - 5 Enable.................................................... 104
6.6.1.5 Actuator 1 - 5 Current Limit.......................................... 104
6.6.1.6 Actuator Timeout ..........................................................105
6.6.1.7 Actuator Open Circuit Test.......................................... 105
6.6.1.8 Joystick Actuators......................................................... 105
6.6.1.9 Actuator buttons are bi-directional ........................... 106
6.6.2 Lighting Settings (CLAM/LM/LMZ)............................. 106
6.6.2.1 CLAM Lighting Enable.................................................. 107
6.6.2.2 Lighting Module Enable ............................................... 107
6.6.2.3 Lighting Module is Critical............................................ 107
6.6.2.4 Side Lights Enable.......................................................... 108
6.6.2.5 Indicators Enable........................................................... 108
6.6.2.6 Hazard Lights Enable .................................................... 108
6.6.2.7 Remember Hazard State ............................................. 108
6.6.3 Remote Control Settings (ARC/RSM).......................109
6.6.3.1 ARC Enable.................................................................... 109
6.6.3.2 ARC Always Drives Actuators 1&2.............................. 109
6.6.3.3 ARC Drives Actuators 1&2 in Profile 0......................... 109
6.6.3.4 ARC Drives Actuator 3, 4, 5.......................................... 110
6.6.4 Environment Control Settings (ECU1/ECU2)............ 111
6.6.4.1 ECU Enable..................................................................... 111
6.6.4.2 ECU Channel ENABLE ................................................... 111