Why are characters deformed during pen plotting on my GRAPHTEC FC8000?
If characters or lines are deformed during pen plotting on your GRAPHTEC Plotter, the plotter is likely in cutting mode. Select PEN as the tool in the CONDITION setting.
Why does the media jump out on my GRAPHTEC FC8000 Plotter?
If the media jumps out to the forward side on your GRAPHTEC Plotter, check the type of media selected: 'SHEET', 'ROLL-1 REAR SET', or 'ROLL-2 REAR SET'. Selecting the wrong type of media can cause this issue.
Why are the cutting conditions disregarded on my GRAPHTEC Plotter?
If the currently selected cutting conditions are disregarded or cannot be changed on your GRAPHTEC Plotter: * Change the setting of the priority to MANUAL, as the parameter priority setting may be set to PROGRAM. * Check the operation, as the [ENTER] key may not have been pressed after changing the settings.
What causes a push roller to go off the media on a GRAPHTEC FC8000 Plotter?
If one of the push rollers goes off the media on your GRAPHTEC Plotter, the leading or trailing edge of the media is not cut straight. Cut the edge of the media straight.
Why won't my GRAPHTEC FC8000 Plotter turn on?
If neither the USER1 nor USER2 lamp lights up and nothing is displayed on the LCD panel of your GRAPHTEC Plotter, there is no power supplied. Check that the power cord is securely connected to the plotter's AC line inlet and the electrical outlet. Also, verify that the electrical outlet is receiving power.
Why is my GRAPHTEC FC8000 Plotter cutting with the origin point shifted?
If your GRAPHTEC Plotter is cutting with the origin point shifted to the center of the media, it's likely because data created with a lower-left origin point is being received when the plotter is set to a center origin point (using HP-GL command). Reset the origin point to the center in the application software, or reset the origin point of the plotter to lower left.
What to do if cut media is hard to weed after cutting with GRAPHTEC Plotter?
If media cut with your GRAPHTEC Plotter is hard to weed afterwards, or cannot be pulled up using a retack sheet: * Switch to a stickier retack sheet, as the current one may not be sticky enough. * Reduce the blade length, as the media might be getting entangled during cutting. * Promptly weed cut media, as cleaning may have been postponed too long.
Why is my GRAPHTEC FC8000 making abnormal noise and discoloring media?
If your GRAPHTEC Plotter is generating abnormal noise from the tool carriage during cutting and the media is discolored where the blade has passed, it is because the media is being rubbed by the tip of the tool plunger. Adjust the blade length and the cutting FORCE settings.
How to improve coarse resolution of curved lines on GRAPHTEC FC8000 Plotter?
To address coarse resolution of curved lines on your GRAPHTEC Plotter: * Adjust the software's resolution setting, as it may be too low. * Increase the value for the blade offset angle, as it may be too low.
Why does the cut line start out crooked on my GRAPHTEC FC8000 Plotter?
If the cut line starts out crooked on your GRAPHTEC Plotter: * Remove any foreign matter inside the holder, as the blade mounted in the tool holder may not be rotating smoothly. * Replace the blade with a new one which has a spring, as the CB09UA spring may have come loose from the blade.
Explains the ranking and meaning of safety precautions and symbols used throughout the manual.
Defines the meaning of DANGER, WARNING, CAUTION, and other safety symbols.
Verify that all standard accessories are present for the plotter.
Identify and understand the names of the plotter's parts and their functions.
Instructions for assembling the plotter, including stand and loading directions.
Steps to connect the plotter to a computer using interface cables (USB, LAN, RS-232C).
Details on cutter pen nomenclature, structure, and blade length adjustment.
Procedure for mounting cutter pens or plotter pens onto the plotter's tool holder.
Instructions for loading roll and sheet media correctly into the plotter.
Guide on positioning push rollers to ensure proper media alignment and feeding.
Step-by-step instructions for powering on the plotter and initial setup display.
Explains how to raise or lower the tool (pen) using the control panel.
Details methods for continuously or stepwise moving the tool carriage and media.
Procedure for defining the starting point for cutting or plotting operations.
Instructions for pausing, resuming, or fully stopping the cutting process.
Covers settings for cutting area, width, page length, mirroring, and scaling.
Details how to perform duplicate cutting of data stored in the plotter's buffer memory.
Provides an overview of ARMS, including mark types, scan range, and positioning.
Covers necessary settings and adjustments for successfully scanning registration marks.
Step-by-step guide for manually adjusting the plotter's axes and position.
Explains tangential emulation for precise corner cutting, especially with thick media.
Corrects length deviations in cuts due to media by applying percentage-based adjustments.
Allows cutting with perforated lines to prevent parts from falling off, with various patterns.
Enhances cutting efficiency by sorting data for area and tool movements.
Enables automatic media feeding upon receiving cutting data to prevent shifting.
Configures USB, Network (LAN), and RS-232C interfaces for plotter communication.
Allows selection of the display language for the plotter's control panel from multiple options.
Enables or disables media sensors that detect the size of the medium.
Configures the plotter to accept GP-GL, HP-GL, or AUTO commands from the software.
Sets priority for tool condition settings between the control panel and computer software.
Outlines daily cleaning and care practices to ensure optimal plotter performance.
Detailed instructions for safely removing and replacing the cutter blade.
Diagnosing and resolving issues when the plotter does not operate or works incorrectly.
Explains how to access and interpret error messages displayed on the plotter's screen.
Instructions for attaching and using the loupe for precise alignment tasks.
Details the attachment and use of the pouncing tool for creating punched outlines.
A diagram illustrating the hierarchical structure of the plotter's menu system.
Provides detailed technical data including CPU, area, speed, pressure, and interface.
General| Cutting Method | Drag knife |
|---|---|
| Repeatability | ±0.1 mm |
| Command Sets | GP-GL/HP-GL |
| Power Supply | AC 100-240V, 50/60Hz |
| Supported OS | Windows, Mac OS |
| Cutting Force | 30-500 gf |
| Maximum Cutting Speed | 1485 mm/s |
| Connectivity | USB 2.0, Ethernet |
| Media Types | Vinyl, Film, Reflective |
| Mechanical Resolution | 0.005 mm |
| Programmable Resolution | 0.025 mm |
| Model | FC8000-100, FC8000-130, FC8000-160 |
To Next Page
