GRAPHTEC FC8600 SERIES - Page 279

16-2
16-3
HP-GL Command Error Display ................................... 13-4
I
Indicator Lamp ............................................................. 2-17
Initial Blade Direction Adjust ........................................
7-18
Interface Setting Menu ...................................................
9-3
ISM ...................................................................... 5-22, 5-26
L
Loading Roll Media (Front Loading "FRONT SET") ........ 2-9
Loading Roll Media (Rear Loading "REAR SET") ...........
2-6
Loading Sheet Media ...................................................
2-11
M
Machine Caution Label ..................................................... v
Main Specifications ......................................................
15-6
Manually ....................................................................... 3-15
Manual Position Adjust ............................................
6-1, 6-2
Mark Distance ..............................................................
5-12
Mark Scan Mode ............................................................
6-2
Mark Size ......................................................................
5-11
Media .............................................................................. 2-6
Media lock ......................................................................
1-4
Media sensor ..................................................................
1-3
Media set lever ...............................................................
1-4
Media stocker .................................................................
1-4
Media That Registration Mark Cannot be Detected .......
5-5
MENU key .....................................................................
2-17
Menu Keys ....................................................................
2-17
Model ID Response ......................................................
11-8
Move Away the Tool Carriage .........................................
3-5
Move in Steps Manually .................................................
3-3
Move the Tool Carriage and Media ................................
3-3
Moving the Pen While Raised or Lowered in Response
to the "W" Command (COMMAND "W") ......................
11-7
N
Network (LAN) Interface ................................................. 9-2
Network interface ...........................................................
1-4
Nomenclature ................................................................. 1-3
Notes on the Stand ............................................................
v
O
Offset Between the Registration Mark and Cutting Origin
Points ......................................................................... 5-16
Option ........................................................................... 14-1
Options ......................................................................... 15-8
ORIGIN key ..................................................................
2-17
origin point movement ....................................................
3-8
Origin Points .................................................................
5-16
Outline of ARMS .............................................................
5-2
Overcut ........................................................................... 7-4
P
Panel Cutting ................................................................ 4-24
Paper-Weight ................................................................ 7-21
Pen Assignment ...........................................................
14-5
Pen station ......................................................................
1-3
Plotting Registration Mark for Adjustment ....................
5-27
Positioning of the Media and the Registration Mark .......
5-4
Position of the Origin Point and the Registration Mark ...
5-5
Pouncing ............................................................. 14-2, 14-3
Power switch ..................................................................
1-3
Pre Feed .......................................................................
2-23
Pre Feed of Media (Paper or Marking Film) ................. 2-23
Printing the Setting of the Plotter ................................
13-16
Priority of Tool Condition Selection ...............................
11-3
Push roller .......................................................................
1-3
Push roller hold-down force switching lever
................... 1-4
R
Raise or Lower the Tool .................................................. 3-2
Reading the Screen (LCD) ...........................................
2-18
Reference Angle ...........................................................
7-11
Replacing Cutter Blade ................................................
12-3
Replacing the Cross Cut Unit .......................................
12-4
RS-232C Interface ..........................................................
9-2
RS-232C interface ..........................................................
1-4
S
Scan Range Necessary to Detect the Registration Mark
.....................................................................................
5-3
Selecting Tool Condition ...............................................
2-24
Self Diagnostic Test ....................................................
13-24
Sensor Level .................................................................
5-18
Setting and Adjustment of ARMS ...................................
5-6
Setting Cutting Area .......................................................
4-2
Setting Cutting Width ......................................................
4-4
Setting Enlarge/Shrink Scale ..........................................
4-8
Setting Feeding Method ...............................................
2-20
Setting Interface .............................................................
9-2
Setting Length of the Page .............................................
4-5
Setting Mirror ..................................................................
4-6
Setting of Step Movement Distance ...............................
3-4
Setting of the Cross Cut Force .....................................
3-17
Setting of the Initial Down Force .....................................
7-6
Setting priority ..............................................................
11-3
Settings for Cutting .........................................................
4-2
Setting the Acceleration ...............................................
2-30
Setting the Cutting Direction ........................................
3-10
Setting the Display Length Unit ....................................
10-3
Setting the Force ..........................................................
2-29
Setting the Origin Point ...................................................
3-7
Setting the Separator ....................................................
4-22
Setting the Space Rear ................................................
4-23
Setting the Speed .........................................................
2-28
Setting the Tangential Mode ...........................................
7-3
Setting the Tool .............................................................
2-26
Setting the Tool Condition .............................................
2-25
Setting the Tool Number ...............................................
2-32
Setting to Default ............................................................
3-6
Shape (Pattern) of Registration Mark ......................
5-2, 5-9
Sorting the Cutting Data .................................................
8-2
Special Precautions on Handling Blades ..........................
iv
Specifications ............................................................... 15-1
Speed of the Registration Mark Scan ...........................
5-26
Stand .............................................................................. 1-3
Standby of the Push Roller ...........................................
2-13
Step Pass .......................................................................
7-9
Stock rollers ....................................................................
1-4
Stop Cutting ..................................................................
3-12
Storing the Plotter .........................................................
12-2
Structure of Cutter Pen ...................................................
2-2
Supplies ........................................................................ 15-9
T
Tangential Mode ............................................................. 7-2
Test Pattern .................................................................
13-18