4-22 4. Azbil
IBS (air-fuel ratio controller)
Set the baud rate by the jumper setting (J2) on the CPU board.
(Underlined setting: default)
Available Device Memory
The available setting range of device memory varies depending on the controller model. Be sure to set within the range
available for the controller to be used. Use [TYPE] when assigning indirect device memory for macro programs.
Item Setting Remarks
J2
RS-485
Baud rate setting
9600 bps: short-circuited between 1 and 2, 3 and 4,
open between 5 and 6
4800 bps: open between 1 and 2, short-circuited
between 3 and 4, open between 5 and 6
Device Memory (Parameter Type ID) TYPE Remarks
000 (NA area) 00H AHC2001, double-word
001 (H/W information) 01H AHC2001, double-word, read only
002 (calendar time setting) 02H AHC2001, double-word
0C3 (calendar time display) 03H AHC2001, double-word, read only
0D0 (system information data) 04H AHC2001, double-word, read only
0D1 (unit information data) 05H AHC2001, double-word, read only
0D2 (CPU unit RS-232C setting) 06H AHC2001, double-word, read only
0D3 (system operation setting) 07H AHC2001, double-word, read only
0D4 (system configuration setting) 08H AHC2001, double-word, read only
0D5 (analog cycle setting) 09H AHC2001, double-word, read only
0D6 (memory capacity monitor) 0AH AHC2001, double-word, read only
201 (PID_A setting) 0BH AHC2001, double-word
202 (PID_A constant) 0CH AHC2001, double-word
203 (PID_A monitor) 0DH AHC2001, double-word, read only
211 (PID_CAS setting) 0EH AHC2001, double-word
212 (PID_CAS constant: master side) 0FH AHC2001, double-word
213 (PID_CAS constant: slave side) 10H AHC2001, double-word
214 (PID_CAS monitor) 11H AHC2001, double-word, read only
234 (Ra_PID setting) 12H AHC2001, double-word
235 (Ra_PID constant) 13H AHC2001, double-word
236 (Ra_PID monitor) 14H AHC2001, double-word, read only
241 (UP_PID setting) 15H AHC2001, double-word
242 (UP_PID constant) 16H AHC2001, double-word
243 (UP_PID monitor) 17H AHC2001, double-word, read only
301 (TBL/TBR setting) 18H AHC2001, double-word
600 (PLC link basic setting) 19H AHC2001, double-word, read only
801 (user-defined area) 1AH AHC2001, double-word
802 (user-defined area) 1BH AHC2001, double-word
803 (user-defined area) 1CH AHC2001, double-word
804 (user-defined area) 1DH AHC2001, double-word
805 (user-defined area) 1EH AHC2001, double-word
806 (user-defined area) 1FH AHC2001, double-word
807 (user-defined area) 20H AHC2001, double-word
808 (user-defined area) 21H AHC2001, double-word
809 (user-defined area) 22H AHC2001, double-word
80A (user-defined area) 23H AHC2001, double-word
80B (user-defined area) 24H AHC2001, double-word
80C (user-defined area) 25H AHC2001, double-word
80D (user-defined area) 26H AHC2001, double-word
80E (user-defined area) 27H AHC2001, double-word
80F (user-defined area) 28H AHC2001, double-word
810 (user-defined area) 29H AHC2001, double-word
811 (user-defined area) 2AH AHC2001, double-word
812 (user-defined area) 2BH AHC2001, double-word
813 (user-defined area) 2CH AHC2001, double-word
814 (user-defined area) 2DH AHC2001, double-word
815 (user-defined area) 2EH AHC2001, double-word
816 (user-defined area) 2FH AHC2001, double-word
817 (user-defined area) 30H AHC2001, double-word
To Next Page
Loading...
