EasyManuals Logo
Home>HPE>Network Router>FlexNetwork MSR Series

HPE FlexNetwork MSR Series Comware 5 Security Configuration Guide

HPE FlexNetwork MSR Series
547 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #195 background imageLoading...
Page #195 background image
182
# Apply the IPsec transform set.
[RouterA-ipsec-policy-isakmp-map1-10] transform-set tran1
# Apply the ACL.
[RouterA-ipsec-policy-isakmp-map1-10] security acl 3101
# Apply the IKE peer.
[RouterA-ipsec-policy-isakmp-map1-10] ike-peer peer
[RouterA-ipsec-policy-isakmp-map1-10] quit
# Configure the IP address of the serial interface.
[RouterA] interface serial 2/1
[RouterA-Serial2/1] ip address 2.2.2.1 255.255.255.0
# Apply the IPsec policy group to the interface.
[RouterA-Serial2/1] ipsec policy map1
2. Configure Router B:
# Define an ACL to identify data flows from subnet 10.1.2.0/24 to subnet 10.1.1.0/24.
<RouterB> system-view
[RouterB] acl number 3101
[RouterB-acl-adv-3101] rule permit ip source 10.1.2.0 0.0.0.255 destination 10.1.1.0
0.0.0.255
[RouterB-acl-adv-3101] quit
# Configure a static route to Host A.
[RouterB] ip route-static 10.1.1.0 255.255.255.0 serial 2/2
# Create an IPsec transform set named tran1.
[RouterB] ipsec transform-set tran1
# Specify the encapsulation mode as tunnel.
[RouterB-ipsec-transform-set-tran1] encapsulation-mode tunnel
# Specify the security protocol as ESP.
[RouterB-ipsec-transform-set-tran1] transform esp
# Specify the algorithms for the IPsec transform set.
[RouterB-ipsec-transform-set-tran1] esp encryption-algorithm des
[RouterB-ipsec-transform-set-tran1] esp authentication-algorithm sha1
[RouterB-ipsec-transform-set-tran1] quit
# Configure the IKE peer.
[RouterB] ike peer peer
[RouterB-ike-peer-peer] pre-shared-key abcde
[RouterB-ike-peer-peer] remote-address 2.2.2.1
[RouterB-ike-peer-peer] quit
# Create an IPsec policy that uses IKE for IPsec SA negotiation.
[RouterB] ipsec policy use1 10 isakmp
# Apply the ACL.
[RouterB-ipsec-policy-isakmp-use1-10] security acl 3101
# Apply the IPsec transform set.
[RouterB-ipsec-policy-isakmp-use1-10] transform-set tran1
# Apply the IKE peer.
[RouterB-ipsec-policy-isakmp-use1-10] ike-peer peer
[RouterB-ipsec-policy-isakmp-use1-10] quit
# Configure the IP address of the serial interface.
[RouterB] interface serial 2/2

Table of Contents

Other manuals for HPE FlexNetwork MSR Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HPE FlexNetwork MSR Series and is the answer not in the manual?

HPE FlexNetwork MSR Series Specifications

General IconGeneral
BrandHPE
ModelFlexNetwork MSR Series
CategoryNetwork Router
LanguageEnglish

Related product manuals