[PE2-mpls-ldp] quit
[PE2] interface vlanif 30
[PE2-Vlanif30] mpls
[PE2-Vlanif30] mpls ldp
[PE2-Vlanif30] quit
Step 5 Create remote LDP sessions between PEs.
# Configure PE1.
[PE1] mpls ldp remote-peer 3.3.3.9
[PE1-mpls-ldp-remote-3.3.3.9] remote-ip 3.3.3.9
[PE1-mpls-ldp-remote-3.3.3.9] quit
# Configure PE2.
[PE2] mpls ldp remote-peer 1.1.1.9
[PE2-mpls-ldp-remote-1.1.1.9] remote-ip 1.1.1.9
[PE2-mpls-ldp-remote-1.1.1.9] quit
After the configuration, run the display mpls ldp session command on PE1 to view the status
of the LDP session. You can see that an LDP session is set up between PE1 and PE2.
The display on PE1 is as follows:
<PE1> display mpls ldp session
LDP Session(s) in Public Network
------------------------------------------------------------------------------
Peer-ID Status LAM SsnRole SsnAge KA-Sent/Rcv
------------------------------------------------------------------------------
2.2.2.9:0 Operational DU Passive 000:15:29 3717/3717
3.3.3.9:0 Operational DU Passive 000:00:00 2/2
------------------------------------------------------------------------------
TOTAL: 2 session(s) Found.
LAM : Label Advertisement Mode SsnAge Unit : DDD:HH:MM
Step 6 Enable MPLS L2VPN on the PEs and create VC connections.
# On PE1, create a VC connection on GE 1/0/0.1 that is connected to CE1.
[PE1] mpls l2vpn
[PE1-l2vpn] mpls l2vpn default martini
[PE1-l2vpn] quit
[PE1] interface gigabitethernet 1/0/0.1
[PE1-GigabitEthernet1/0/0.1] control-vid 1000 qinq-termination
[PE1-GigabitEthernet1/0/0.1] qinq termination pe-vid 100 ce-vid 10
[PE1-GigabitEthernet1/0/0.1] mpls l2vc 3.3.3.9 101
[PE1-GigabitEthernet1/0/0.1] quit
# On PE2, create a VC connection on GE 2/0/0.1 that is connected to CE1.
[PE2] mpls l2vpn
[PE2-l2vpn] mpls l2vpn default martini
[PE2-l2vpn] quit
[PE2] interface gigabitethernet 2/0/0.1
[PE2-GigabitEthernet2/0/0.1] control-vid 2000 qinq-termination
[PE2-GigabitEthernet2/0/0.1] qinq termination pe-vid 100 ce-vid 10
[PE2-GigabitEthernet2/0/0.1] mpls l2vc 1.1.1.9 101
[PE2-GigabitEthernet2/0/0.1] quit
Step 7 Verify the configuration.
On PEs, check the L2VPN connections. You can see that an L2VC connection is set up and is
in Up state.
Take the display on PE1 as an example.
Quidway S7700 Smart Routing Switch
Configuration Guide - Ethernet 5 QinQ Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
241
To Next Page
Loading...
