Instron CEAST 9340 - Page 108

179 pages

Save Page as PDF

To Next Page

To Previous Page

Page 108 - CEAST 9340 - Instructions for Use and Maintenance 7510.000MN1r ed. 1 rev. 1

Fig. 2 - Environmental Chamber Electric Board (rear side of instrument)

Environmental Chamber Electric Board

Fuses to be used as spare parts:

CEAST code 0200.850 Quick Fuse 5 x 20 1.5A

CEAST code 0200.855 Fuse 5 x 20 0.5A

CEAST code 0201.184 Quick Fuse Omega 16A Code GL138316

Fuse

holder

Main Page

Default Chapter2
- Table of Contents2
Legend7
1 General Information8
- Equipment Description11
- Introduction11
- Modularity11
- Difference between Instruments11
- Main Parts of Instrument11
- Options13
- Technical Characteristics14
- Layout16
- Safety17
2 Conditions of Use18
- Authorized Personnel18
- Normal Use Conditions19
- Abnormal Situations20
3 Operator Work Station21
- Shields21
- Residual Risks21
4 Transport and Movement22
- Lifting and Handling22
- Movement in Packaging22
- Movement of the Instrument22
- Weight of the Main Parts23
- Check for Possible Damage23
- Storage23
5 Mounting and Dismantling24
- Dismantling the Packaging Case24
6 Installation25
- Space and Environment Requirements25
- Space25
- Environment25
- Services25
- Positioning26
- Surface Load in Static Condition26
- Load on Slab27
- Installation Procedure28
- Levelling32
- Stability33
- Cleaning33
- Materials and Products33
7 Start-Up34
- Instrument, Ceast das 8000 Junior/Ceast 16000 and Pc Connection34
- Electrical Service Connection34
- Pneumatic Service Connection35
- Cryogenic Service Connection36
8 Use38
- Safety Standards38
- Component Identification39
- Safeties and Their Locations41
- Commands43
- Operations44
- Key Functions44
- Program45
- Program Start - up47
- Navigation through the Program Menus48
- Main Menu50
- Set Temperature51
- Load Parameters51
- Modify Parameters52
- Save Parameters56
- Results56
- Utility57
- Input Password58
- Cycle Counter59
- Fw Version59
- Modify Password60
- Clock60
- Language61
- Service61
- Shutter Moving62
- Striker Release62
- Move to Height63
- Visualize Sensors63
- Visualize I/O64
- Emergencies Synoptic64
- Error Codes in the Program64
- Preparing the Instrument for Testing65
- Replacement of the Stands65
- Replacement of the Specimen Fixtures66
- Replacement of the Striker Holder74
- Replacement of the Weights76
- Replacement of Striker78
- Replacement of the Striker Extension81
- REPLACEMENT of the STRIKER'S HEADS (Interchangeable Head Type)82
- Preparing the Instrument for Tensile-Impact Test Only86
- Program Setting86
- Replacement of the Fixed Height Vice Support Stand88
- Replacement of the Piezoelectric Force Sensor90
- Replacement of the Instrumented Vice for Tensile-Impact92
- Replacement of the Tensile-Impact Specimen95
- Replacement of Striker for Tensile-Impact Tests97
- Support Stands Codes 7520.350 and 7520.351 for Plates of Fiber Reinforced Polymers98
- Introduction98
- Components Identification98
- Disassembly and Assembly of the Support Stands99
- Special-Purpose Tooling for Impact Tests on Pipes100
- Introduction100
- Supports100
- Special Heads for Striker102
- Carry out Test103
- Operating Sequence of an Instrumented Test103
- Screens Shown During Test104
- Test Start104
- Test in Progress104
- Test End105
9 Maintenance106
- Safety Standards, General Procedure106
- Fuses Replacement107
- Cleaning and Drying Methods109
- Procedure for Loading Firmware Updates110
- Connection110
- Preparation of the Loading Program110
- Loading113
- Loader Upgrade114
- Firmware Upgrade114
- Disconnection115
- Instrument Firmware Check115
- Replacement of the Impact Rollers116
- Greasing the Striker Releasing Mechanism117
- Lubricating the Gearing Chain118
- Verifying the Gearing Chain Tightening119
10 Spare Parts120
- List of Recommended Spare Parts120
- Ceast 9340 7515.000 and 7516.000120
- List of Spare Parts for Technical Assistance121
- Ceast 9340 Code 7515.000 and 7516.000121
- Environmental Chamber 7510.011124
- Striker Antirebound System Code 7510.002125
11 Training126
- General Information126
12 Wiring Diagrams127
13 Pneumatic Diagrams148
Appendix A - Ceast 9340 Part List151
Appendix B - Tooling154
Appendix C - Tooling for Tensile Impact Test Only160
Appendix D - Strikers Technical Features161
Appendix E - Input List165
Appendix F - Output List167

Instron CEAST 9340 - Page 108

Table of Contents

Related product manuals