To Next Page

To Previous Page

Verify the Front I/O Assembly

132 SPARC T5-8 Server Service Manual • November 2015

faultmgmtsp>

Use the fmadm faulty command to determine if the server is operating normally.

■

If a fault was detected, see “Diagnostics Process” on page 25.

■

If no fault was detected, the front I/O assembly was installed successfully.

Related Information

■

“Remove the Front I/O Assembly” on page 127

■

“Install the Front I/O Assembly” on page 130

Default Chapter5
- Table of Contents5
Using this Documentation11
Identifying Components13
- Front Panel Components (Service)14
- Rear Panel Components (Service)15
- DIMM Locations16
- Front Panel Components (Service)16
- Main Module Internal Component Locations17
- Supported Storage Devices18
- Fan Module Locations20
- Rear I/O Module Port Locations21
- Chassis Subassembly Components22
- Component Service Task Reference23
Detecting and Managing Faults25
- Understanding Diagnostics25
- Interpreting Leds29
  - Front Panel Controls and Leds31
  - Rear Panel Controls and Leds33
- Configuring POST35
- Managing Faults41
- Interpreting Log Files and System Messages45
Preparing for Service49
- Safety Information49
- Tools Needed for Service51
- Filler Panels and Modules51
- Component Service Categories52
- Find the Server Serial Number52
- Locate the Server53
- Removing Power from the Server53
- Prevent ESD Damage57
Servicing Processor Modules59
- Server Upgrade Process59
- Processor Module Leds61
- Determine Which Processor Module Is Faulty62
- Remove a Processor Module or Processor Filler Module63
- Install a Processor Module or Processor Filler Module67
- Verify the Processor Module70
Servicing Dimms71
- DIMM Configuration71
  - DIMM Guidelines72
  - DIMM Locations72
- Determine Which DIMM Is Faulty (FMA)73
- Determine Which DIMM Is Faulty (Leds)75
- DIMM Configuration Fault Messages76
- Remove a DIMM or DIMM Filler Panel76
- SPARC T5-8 Server Service Manual • November76
- Install a DIMM78
- Verify the DIMM80
Servicing Hard Drives81
- Hard Drive Leds82
- Determine Which Hard Drive Is Faulty82
- Remove a Hard Drive83
- Install a Hard Drive85
- Verify the Hard Drive86
Servicing the Main Module89
- Main Module Leds90
- Determine if the Main Module Is Faulty91
- Remove the Main Module91
- Install the Main Module95
- Verify the Main Module97
Servicing the Storage Backplanes99
- Remove a Storage Backplane99
- Install a Storage Backplane103
- Verify the Storage Backplane107
Servicing the Service Processor Card109
- Determine if the Service Processor Card Is Faulty109
- Remove the Service Processor Card110
- Install the Service Processor Card112
- Verify the Service Processor Card114
Servicing the System Configuration PROM117
- Remove the System Configuration PROM118
- Install the System Configuration PROM119
- Verify the System Configuration PROM120
Servicing the Battery123
- Remove the Battery123
- Install the Battery125
- Verify the Battery126
Servicing the Front I/O Assembly127
- Remove the Front I/O Assembly127
- Install the Front I/O Assembly130
- Verify the Front I/O Assembly131
Servicing Power Supplies133
- Power Supply Leds134
- Determine Which Power Supply Is Faulty134
- Remove a Power Supply135
- Install a Power Supply137
- Verify the Power Supply138
Servicing Fan Modules141
- Fan Module LED141
- Determine Which Fan Module Is Faulty142
- Remove a Fan Module143
- Install a Fan Module145
- Verify the Fan Module146
Servicing Pcie Cards149
- Understanding Pcie Root Complex Connections149
  - Root Complex Connections (Four Processor Modules)150
  - Root Complex Connections (Two Processor Modules)151
- Pcie Card Installation Guidelines153
- Pcie Carrier Leds and Controls154
- Determine Which Pcie Card Is Faulty155
- Remove a Card Carrier155
- Remove a Pcie Card159
- Remove a Carrier Extension162
- Install a Carrier Extension164
- Install a Pcie Card165
- Install a Card Carrier168
- Verify the Pcie Card171
Servicing the Rear I/O Module173
- Determine if the Rear I/O Module Is Faulty173
- Remove the Rear I/O Module174
- SPARC T5-8 Server Service Manual • November174
- Install the Rear I/O Module176
- Verify the Rear I/O Module178
Servicing the Rear Chassis Subassembly181
- Determine if the Rear Chassis Subassembly Is Faulty181
- Remove the Rear Chassis Subassembly182
- Determine Your Next Step183
- Install the Rear Chassis Subassembly185
- Verify the Rear Chassis Subassembly188
Returning the Server to Operation191
- Connect the Power Cords191
- Power on the Server (Oracle ILOM)192
- Power on the Server (Power Button)193
Glossary195
Index201

Brand	Oracle
Model	SPARC T5-8
Category	Server
Language	English

Oracle SPARC T5-8 User Manual

Table of Contents

Other manuals for Oracle SPARC T5-8

Questions and Answers:

Oracle SPARC T5-8 Specifications

Related product manuals