Oracle SPARC T5-8 - Page 167

206 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Install a PCIe Card

Servicing PCIe Cards 167

5.

Ensure that the card's bulkhead notch is aligned properly with the carrier's

bulkhead pin so that the cover enages the pin.

Table of Contents

Default Chapter5
- Table of Contents5
Using this Documentation11
Identifying Components13
- Front Panel Components (Service)14
- Rear Panel Components (Service)15
- DIMM Locations16
- Front Panel Components (Service)16
- Main Module Internal Component Locations17
- Supported Storage Devices18
- Fan Module Locations20
- Rear I/O Module Port Locations21
- Chassis Subassembly Components22
- Component Service Task Reference23
Detecting and Managing Faults25
- Understanding Diagnostics25
- Interpreting Leds29
  - Front Panel Controls and Leds31
  - Rear Panel Controls and Leds33
- Configuring POST35
- Managing Faults41
- Interpreting Log Files and System Messages45
Preparing for Service49
- Safety Information49
- Tools Needed for Service51
- Filler Panels and Modules51
- Component Service Categories52
- Find the Server Serial Number52
- Locate the Server53
- Removing Power from the Server53
- Prevent ESD Damage57
Servicing Processor Modules59
- Server Upgrade Process59
- Processor Module Leds61
- Determine Which Processor Module Is Faulty62
- Remove a Processor Module or Processor Filler Module63
- Install a Processor Module or Processor Filler Module67
- Verify the Processor Module70
Servicing Dimms71
- DIMM Configuration71
  - DIMM Guidelines72
  - DIMM Locations72
- Determine Which DIMM Is Faulty (FMA)73
- Determine Which DIMM Is Faulty (Leds)75
- DIMM Configuration Fault Messages76
- Remove a DIMM or DIMM Filler Panel76
- SPARC T5-8 Server Service Manual • November76
- Install a DIMM78
- Verify the DIMM80
Servicing Hard Drives81
- Hard Drive Leds82
- Determine Which Hard Drive Is Faulty82
- Remove a Hard Drive83
- Install a Hard Drive85
- Verify the Hard Drive86
Servicing the Main Module89
- Main Module Leds90
- Determine if the Main Module Is Faulty91
- Remove the Main Module91
- Install the Main Module95
- Verify the Main Module97
Servicing the Storage Backplanes99
- Remove a Storage Backplane99
- Install a Storage Backplane103
- Verify the Storage Backplane107
Servicing the Service Processor Card109
- Determine if the Service Processor Card Is Faulty109
- Remove the Service Processor Card110
- Install the Service Processor Card112
- Verify the Service Processor Card114
Servicing the System Configuration PROM117
- Remove the System Configuration PROM118
- Install the System Configuration PROM119
- Verify the System Configuration PROM120
Servicing the Battery123
- Remove the Battery123
- Install the Battery125
- Verify the Battery126
Servicing the Front I/O Assembly127
- Remove the Front I/O Assembly127
- Install the Front I/O Assembly130
- Verify the Front I/O Assembly131
Servicing Power Supplies133
- Power Supply Leds134
- Determine Which Power Supply Is Faulty134
- Remove a Power Supply135
- Install a Power Supply137
- Verify the Power Supply138
Servicing Fan Modules141
- Fan Module LED141
- Determine Which Fan Module Is Faulty142
- Remove a Fan Module143
- Install a Fan Module145
- Verify the Fan Module146
Servicing Pcie Cards149
- Understanding Pcie Root Complex Connections149
  - Root Complex Connections (Four Processor Modules)150
  - Root Complex Connections (Two Processor Modules)151
- Pcie Card Installation Guidelines153
- Pcie Carrier Leds and Controls154
- Determine Which Pcie Card Is Faulty155
- Remove a Card Carrier155
- Remove a Pcie Card159
- Remove a Carrier Extension162
- Install a Carrier Extension164
- Install a Pcie Card165
- Install a Card Carrier168
- Verify the Pcie Card171
Servicing the Rear I/O Module173
- Determine if the Rear I/O Module Is Faulty173
- Remove the Rear I/O Module174
- SPARC T5-8 Server Service Manual • November174
- Install the Rear I/O Module176
- Verify the Rear I/O Module178
Servicing the Rear Chassis Subassembly181
- Determine if the Rear Chassis Subassembly Is Faulty181
- Remove the Rear Chassis Subassembly182
- Determine Your Next Step183
- Install the Rear Chassis Subassembly185
- Verify the Rear Chassis Subassembly188
Returning the Server to Operation191
- Connect the Power Cords191
- Power on the Server (Oracle ILOM)192
- Power on the Server (Power Button)193
Glossary195
Index201

Other manuals for Oracle SPARC T5-8

Getting Started Guide6 pages

Related product manuals

Preview: Oracle SPARC T5-2

Oracle SPARC T5-2

Preview: Oracle SPARC T5-4

Oracle SPARC T5-4

Preview: Sun SPARC Enterprise T5140

Sun SPARC Enterprise T5140

Preview: Oracle SPARC T8-2

Oracle SPARC T8-2

Preview: Oracle SPARC T7-2

Oracle SPARC T7-2

Preview: Oracle SPARC T8-1

Oracle SPARC T8-1

Oracle SPARC T8 Series

Preview: Oracle Netra SPARC T4-1B

Oracle Netra SPARC T4-1B

Preview: Oracle SPARC

Oracle SPARC M8

Preview: Oracle SPARC S7-2

Oracle SPARC S7-2

Preview: Oracle Netra SPARC S7-2 Series

Oracle Netra SPARC S7-2 Series