Pfaff 3519-5/01 User Manual

147
X111 Y1 A10 CAN1 Thread trimming on
X112 Y2 A10 CAN1 Positioning tube vacuum on
X113 Y3 A10 CAN1 Table vacuum on
X114 Y4 A10 CAN1 Workholder bar down
X115 Y5 A10 CAN1 Workholder bar up
X116 Y6 A10 CAN1 Work surface forwards
X117 Y7 A10 CAN1 Top clamp closed
X118 Y8 A10 CAN1 Disengage bottom clamp
X119 Y9 A10 CAN1 Clamp coupling on
X120 Y10 A10 CAN1 Clamp feed unit to the right
X121 Y11 A10 CAN1 Clamp feed unit to the left
X122 Y12 A10 CAN1 Stacker table up
X123 Y13 A10 CAN1 Needle thread tension closed
X124 Y14 A10 CAN1 Wiper 3 off
X125 Y15 A10 CAN1 Wiper 3 on (upwards)
X126 Y24 A10 CAN1 Vacuum reduction on
X132 Y17 A11 CAN2 Wiper 2 off
X135 Y18 A11 CAN2 Material take-over 1 closed
X136 Y19 A11 CAN2 Material take-over 2 closed
X137 Y20 A11 CAN2 Thread catcher back, engage stationary knife
X138 Y21 A11 CAN2 Engage thread catcher
X139 Y22 A11 CAN2 CAN2 (turn-up limit on)
X133 Y23 A11 CAN2 Wiper 1 off
X140 Y40 A11 CAN2 Cutter down (option - ironing compensation strip)
X141 Y41 A11 CAN2 Slide back (option - ironing compensation strip)
X142 Y42 A11 CAN2 Slide up (option - ironing compensation strip)
X143 Y43 A11 CAN2 Air blast (option - ironing compensation strip)
X151 Y27U1 A12 CAN3 Positioning tube cylinder 1 down (vertical)
X152 Y27U2 A12 CAN3 Positioning cylinder 1 up (vertical)
X153 Y28U1 A12 CAN3 Positioning tube cylinder 2 down (vertical)
X154 Y28U2 A12 CAN3 Positioning cylinder 2 up (vertical)
X155 Y29U1 A12 CAN3 Infeed table lift 1 back
X156 Y29U2 A12 CAN3 Infeed table lift 1 forwards
X157 Y30U1 A12 CAN3 Infeed table lift 2 end positions
X158 Y30U2 A12 CAN3 Infeed table lift 2 special position
X159 Y31U1 A12 CAN3 Positioning tube cylinder 1 back (horizontal)
X160 Y31U2 A12 CAN3 Positioning tube cylinder 1 forwards (horizontal)
X161 Y32U1 A12 CAN3 Positioning tube cylinder 2 back (horizontal)
X162 Y32U2 A12 CAN3 Positioning tube cylinder 2 forwards (horizontal)
X163 Y33 A12 CAN3 Needles forwards
X164 Y34 A12 CAN3 Turn-up at back
X165 Y35 A12 CAN3 Infeed table extension on
X166 Y36 A12 CAN3 Spreader forwards
Y1 A10 CAN1 Thread trimming on
Y2 A10 CAN1 Positioning tube vacuum on
Y3 A10 CAN1 Table vacuum on
Y4 A10 CAN1 Workholder bar down
Y5 A10 CAN1 Workholder bar up
Y6 A10 CAN1 Work surface forwards
Circuit diagrams

Pfaff 3519-5/01 Specifications

General

Brand	Pfaff
Model	3519-5/01
Category	Sewing Machine
Language	English