Summa S2 SERIES - Page 12

S CLASS™ 2 cutter User’s Manual
Table of contents VI
List of Figures
1-1 S CLASS 2 cutter fully boxed ............................................................................................. 1-1
1-2 Contents of the Stand box .................................................................................................. 1-2
1-3 Mounting the horizontal panel ............................................................................................ 1-2
1-4 Mounting feet and casters .................................................................................................. 1-2
1-5 Mounting the basket tubes ................................................................................................. 1-3
1-6 Preparing to install the linen basket ................................................................................... 1-3
1-7 Orientation of the holes in the c-shaped tubes ................................................................... 1-3
1-8 Completely assembled stand for the S CLASS 2 cutter..................................................... 1-4
1-9 Position of the screws ........................................................................................................ 1-4
1-10 S CLASS 2 cutter, front view ............................................................................................ 1-5
1-11 S CLASS 2 cutter, rear view ............................................................................................. 1-7
1-12 Properly grounded connection ....................................................................................... 1-12
1-13 Cutter is loaded and ready ............................................................................................. 1-13
1-14 Cutter is ready - no media loaded .................................................................................. 1-13
1-15 Position pinch rollers ...................................................................................................... 1-18
1-16 reducing pressure ........................................................................................................... 1-19
1-17 Pinch roller lever ............................................................................................................. 1-20
1-18 Media flanges ................................................................................................................. 1-20
1-19 Positioning the media flange on the cutter ..................................................................... 1-20
1-20 Feeding roll media without using media flanges ............................................................ 1-21
1-21 Media position ................................................................................................................ 1-21
1-22 Pinch roller lever ............................................................................................................. 1-22
1-23 Removing the drag knife holder from the clamp ............................................................ 1-27
1-24 Removing the knife from the standard drag knife holder ............................................... 1-27
1-26 Dual clamp drag head .................................................................................................... 1-28
1-27 Knife pressure test pattern ............................................................................................. 1-29
1-28 Removing the tangential knife holder ............................................................................. 1-31
1-29 Removing the knife from the tangential knife holder ...................................................... 1-31
1-30 Blade assembly .............................................................................................................. 1-32
1-31 Inserting the tangential knife holder ............................................................................... 1-32
1-32 Knife depth adjustment ................................................................................................... 1-32
1-33 Knife pressure test pattern ............................................................................................. 1-33
1-34 Razor blade for automatic separation of media ............................................................. 1-36
2-1 Touch screen ...................................................................................................................... 2-1
2-2 screen saver ....................................................................................................................... 2-2
2-3 Online status screen ........................................................................................................... 2-6
2-4 Correct knife offset pattern ................................................................................................. 2-9
2-5 Possible knife calibrations ................................................................................................ 2-10
2-6 Correct tangential knife calibration test ............................................................................ 2-11
2-7 Length calibration pattern ................................................................................................. 2-14
2-8 FLexcut principle .............................................................................................................. 2-16
2-9 Combined contour cut and cutting through ...................................................................... 2-18
2-10 Knife depth setting normal cutting .................................................................................. 2-19
2-11 Knife depth setting cutting through ................................................................................. 2-19
2-12 Knife depth setting normal cutting .................................................................................. 2-20
2-13 Knife depth setting cutting through ................................................................................. 2-20
2-14 Dual head ....................................................................................................................... 2-23
3-1 margins printing on a roll .................................................................................................... 3-2
3-2 OPOS alignment methods .................................................................................................. 3-3
3-3 Positioning the media for multiple sheets ......................................................................... 3-10
3-4 Opos barcode Job loaded ................................................................................................ 3-11
3-5 Opos Cam ........................................................................................................................ 3-16