6
© 2008-2011 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO5520C/6520C/6530C
ERROR CODE and TROUBLESHOOTING
6 - 15
CB82 Finisher related
service call
Finisher - Main CPU program error P. 6-98
CB83 Saddle Stitch Finisher - Main CPU program error P. 6-98
CB84 Hole Punch Unit - Main CPU program error P. 6-98
CB91 Saddle Stitch Finisher flash ROM abnormality P. 6-98
CB92 Saddle Stitch Finisher RAM abnormality P. 6-98
CB93 Additional folding motor abnormality P. 6-99
CB94 Saddle transport motor abnormality P. 6-99
CB95 Stacker motor abnormality P. 6-99
CBA0 Stitch motor (front) abnormality: Stitch motor (front)
is not rotating or rotary cam is not moving normally.
[MJ-1103/1104]
P. 6-100
CBB0 Stitch motor (rear) abnormality: Stitch motor (rear)
is not rotating or rotary cam is not moving normally.
[MJ-1103/1104]
P. 6-100
CBC0 Alignment motor abnormality: Alignment motor is
not rotating or aligning plate is not moving normally.
[MJ-1103/1104]
P. 6-100
CBE0 Paper folding motor abnormality: Paper folding
motor or paper folding roller is not rotating normally.
[MJ-1103/1104]
P. 6-100
CC20 Communication error between finisher and saddle
stitcher: Communication error between finisher
controller PC board and saddle stitcher controller
board [MJ-1103/1104]
P. 6-100
CC30 Stack transport motor abnormality: The stack
transport motor is not rotating or the stack transport
belt is not moving normally. [MJ-1103/1104]
P. 6-101
CC31 Transport motor abnormality: The transport motor is
not rotating or the stack transport roller -1 and -2 is
not rotating normally. [MJ-1103/1104]
P. 6-101
CC41 Paper holder cam home position abnormality: The
paper holder cam is not at the home position. [MJ-
1103/1104]
P. 6-101
CC51 Sideways adjustment motor (M2) abnormality:
Sideways adjustment motor is not rotating or
puncher is not shifting normally. [MJ-1103/1104
(when MJ-6102 is installed)]
P. 6-102
CC52 Skew adjustment motor (M1) abnormality: Skew
adjustment motor is not rotating or puncher is not
shifting normally. [MJ-1103/1104 (when MJ-6102 is
installed)]
P. 6-102
CC60 Punch motor abnormality: Punch motor is not
rotating or puncher is not shifting normally. [MJ-
1103/1104 (when MJ-6102 is installed)]
P. 6-103
CC61 Punch motor (M3) home position detection error:
Punch motor is not rotating or puncher is not
shifting normally. [MJ-1103/1104 (when MJ-6102 is
installed)]
P. 6-103
CC71 Punch ROM checksum error: Abnormality of
checksum value on Hole punch controller PC board
is detected when the power is turned on. [MJ-1103/
1104 (when MJ-6102 is installed)]
P. 6-103
CC72 Punch RAM read/write error: Abnormality of
checksum value on Hole punch controller PC board
is detected when the power is turned on. [MJ-1103/
1104 (when MJ-6102 is installed)]
P. 6-103
CC73 Punching device power supply abnormality P. 6-103
CC74 Punch unit transport pulse abnormality P. 6-103
Error code Classification Contents Troubleshooting
To Next Page
Loading...
