Vanderbilt SPC42 Series - Page 365

Vanderbilt SPC42 Series

368 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Appendix

23

ATP Category Timings

365

Vanderbilt

Installation & Configuration Manual

A6V10276959

01.05.2016

Table of Contents

Default Chapter3
- Table of Contents3
1 Meaning of Symbols11
2 Security12
- Target Group12
- General Safety Instructions12
- Meaning of Written Warning Notices14
- Meaning of Hazard Symbols14
3 Directives and Standards15
- EU Directives15
4 Technical Data31
- Spc400031
- Spc500032
- Spc600035
- Spcp355.30038
5 Introduction39
6 Mounting System Equipment40
- Mounting a G2 Housing40
- Mounting a G3 Housing41
  - Mounting a Back Tamper Kit43
  - Battery Installation for EN50131 Compliance47
- Mounting a G5 Housing48
- Mounting a Keypad54
- Mounting an Expander54
7 Smart PSU55
- SPCP355.300 Smart PSU55
8 Controller Hardware66
- Controller Hardware 42Xx\43Xx\53Xx\63Xx66
- Controller Hardware SPC5350 and 635069
9 Door Expander71
10 Wiring the System72
- Wiring the X-BUS Interface72
- Wiring of Branch Expander81
- Wiring the System Ground82
- Wiring the Relay Output82
- Wiring the Zone Inputs83
- Wiring an External SAB Bell86
- Wiring an Internal Sounder87
- Wiring Glassbreak87
- Installing Plug-In Modules87
11 Powering up the SPC Controller89
- Powering from Battery Only89
12 Keypad User Interface90
- Spck420/42190
- Spck620/62395
13 Software Support Tools101
14 Starting the System102
- Engineer Modes102
  - Engineer Pins102
- Programming Tools103
  - Fast Programmer103
- Configuring Start-Up Settings103
- Creating System Users105
- Programming the Portable ACE105
- Configuring Wireless Fob Devices106
  - Clearing Alerts Using the Fob107
15 Soft Engineer Programming Via the Keypad109
16 Engineer Programming Via the Keypad110
- System Status110
- Options111
- Timers114
- Areas116
- Area Groups117
- X-Bus118
  - X-BUS Addressing118
  - XBUS Refresh118
  - Reconfigure119
  - Keypads/Expanders/Door Controllers120
  - Locate120
  - Monitor120
  - Edit Keypads121
  - Edit Expanders123
  - Edit Door Controllers127
  - Addressing Mode128
  - XBUS Type129
  - Bus Retries129
  - Comms Timer129
- Wireless130
  - Add Sensors130
  - Edit Sensors (Zone Assignment)131
  - Add WPA131
  - Edit WPA132
- Zones132
- Doors133
- Outputs136
  - Outputs Types and Output Ports137
- Communication140
  - Serial Ports140
  - Ethernet Ports140
  - Modems141
  - Monitoring the Transmission Network Interface141
  - Configuring Modems142
  - Central Station143
  - Add143
  - Edit143
  - Delete144
  - Make Test Call144
  - Remote Maintenance144
- Test145
  - Bell Test145
  - Walk Test145
  - Zone Monitor145
  - Output Test146
  - Soak Test147
  - Audible Options147
  - Visual Indicators147
  - WPA Test148
  - Seismic Test148
- Utilities148
- Isolate149
- Event Log149
- Access Log150
- Alarm Log150
- Change Engineer Pin150
- Users150
  - Add151
  - Edit151
  - Access Control151
  - Delete153
- User Profiles154
  - Add154
  - Edit154
  - Delete154
- Sms155
  - Add155
  - Edit156
  - Delete156
- Set Date/Time157
- Installer Text157
- Door Control157
- SPC Connect158
17 Engineer Programming Via the Browser159
- System Information159
- Ethernet Interface159
- Connecting to the Panel Via USB161
- Logging into the Browser163
- SPC Home164
- Panel Status167
- Logs181
- Users183
- Configuration196
- Configuring Communications261
- File Operations304
- Using the Fast Programmer311
18 Accessing Web Server Remotely315
- PSTN Connection315
- GSM Connection317
19 Intruder Alarm Functionality320
- Financial Mode Operation320
- Commercial Mode Operation320
- Domestic Mode Operation321
- Full and Local Alarms321
20 System Examples and Scenarios322
- When to Use a Common Area322
21 Seismic Sensors324
- Seismic Sensor Testing325
22 Blocking Lock Operation328
- Blocking Lock328
- Authorized Setting of the Blocking Lock329
- Locking Element330
23 Appendix332
- Network Cable Connections332
- Controller Status Leds332
- Powering Expanders from the Auxiliary Power Terminals333
- Calculating the Battery Power Requirements334
- Domestic, Commercial and Financial Mode Default Settings336
- Wiring of the X10 Interface337
- SIA Codes337
- CID Codes342
- Overview of Keypad Types343
- User PIN Combinations344
- Duress Pins345
- Automatic Inhibits345
  - Zones345
  - Access Pins345
  - Engineer Access345
  - Keypad User Logoff345
- Wiring of Mains Cable to the Controller346
- Maintenance Controller346
- Maintenance Smart PSU347
- Zone Types347
- Zone Attributes350
- Applicable Attributes to Zone Types352
- ATS Levels and Attenuation Specifications354
- Supported Card Readers and Card Formats354
- SPC Support for E-Bus Devices356
  - Configuring and Addressing E-Bus Devices356
  - Addressing Transponders for SAP 8, SAP 14, and SAP 20358
  - Addressing Transponders for PSU SAP 25358
- Flexc Glossary359
- Flexc Commands360
- ATS Category Timings362
- ATP Category Timings363

Related product manuals

Vanderbilt SPC6350

Vanderbilt SPC6330.320

Vanderbilt SPC5330.320

Vanderbilt SPCP333.300

Vanderbilt SPCA210.100

Vanderbilt SPCP332.300

Vanderbilt SPC53 Series