SHB WL34 * 2.0 12-5
Malfunctions 12
Error code lists
3241 Exhaust-gas treatment temperature sensor 1 15 Valid data, but above the normal range Over 700 °C
- Limited engine speed and torque
- Suppression of necessary regeneration
3241 Exhaust-gas treatment temperature sensor 1 16 Valid data, but above the normal range Over 800 °C and less than 5 V
- Engine stop
- Engine emergency stop
- Suppression of necessary regeneration
3242
Exhaust-gas treatment 1 diesel particulate filter
intake temperature sensor
1 Valid data, but below the normal range Below 50 °C and below the setting
- Limited engine speed and torque
- Suppression of necessary regeneration
- Incorrect soot load estimate
3242
Exhaust-gas treatment 1 diesel particulate filter
intake temperature sensor
3 Voltage too high Below setting and over 5 V
- Limited engine speed and torque
- Suppression of necessary regeneration
- Incorrect soot load estimate
3242
Exhaust-gas treatment 1 diesel particulate filter
intake temperature sensor
4 Voltage too low Over 999 °C and below 0.05 V
- Limited engine speed and torque
- Suppression of necessary regeneration
- Incorrect soot load estimate
3242
Exhaust-gas treatment 1 diesel particulate filter
intake temperature sensor
15 Valid data, but above the normal range Over 700 °C
- Limited engine speed and torque
- Suppression of necessary regeneration
3242
Exhaust-gas treatment 1 diesel particulate filter
intake temperature sensor
16 Valid data, but above the normal range Over 800 °C and less than 5 V
- Engine stop
- Engine emergency stop
- Suppression of necessary regeneration
3251
Exhaust-gas treatment 1 diesel particulate filter
differential pressure sensor
3 Voltage too high Over 5 bar and below 4.75 V
- Limited engine speed and torque
- Incorrect soot load estimate
3251
Exhaust-gas treatment 1 diesel particulate filter
differential pressure sensor
4 Voltage too low 0 bar and over 0.25 V
- Limited engine speed and torque
- Incorrect soot load estimate
3473 Exhaust-gas treatment 7 Mechanism does not react Misfiring in burner
- Suppression of necessary regeneration
- Limited engine power
- Engine speed fluctuating
3473 Exhaust-gas treatment 11 Error during ignition Misfiring in burner
- Suppression of necessary regeneration
- Limited engine power
- Engine speed fluctuating
3484 Exhaust-gas treatment 1 ignition 0 Valid data, but above the normal range Over 12 V - Faulty glow plug
3484 Exhaust-gas treatment 1 ignition 3 Voltage too high Over 21.9 V - Faulty glow plug
3484 Exhaust-gas treatment 1 ignition 4 Voltage too low Under 5.1 V - Suppression of necessary regeneration
3556 Exhaust-gas treatment hydrocarbon dosage 6 Power consumption too high - -
3610 Diesel particulate filter 1 output pressure sensor 3 Voltage too high Over 20 bar and over 4.75 V
- Limited engine speed and torque
- Incorrect soot load estimate
3610 Diesel particulate filter 1 output pressure sensor 4 Voltage too low Below 1.4 bar and below 0.5 V
- Limited engine speed and torque
- Incorrect soot load estimate
3713
Regeneration of diesel particulate filter actively
blocked; Time-out
7 Mechanism does not react
DOC-In temperature incorrect during
regeneration
- Suppression of necessary regeneration
- Limited engine power
- Engine speed fluctuating
3713
Regeneration of diesel particulate filter actively
blocked; Time-out
31 Error Misfiring in burner
- Suppression of necessary regeneration
- Limited engine power
- Engine speed fluctuating
Error code
Error setting condition
(detection threshold)
Reaction MotorSPN (component) FMI (error type)
SPN SPN text FMI FMI text
To Next Page
Loading...
