YASKAWA T1000A - Page 483

D.3 UL Standards
YASKAWA ELECTRIC SIEP C710616 30B YASKAWA AC Drive T1000A Technical Manual 483
Standards Compliance
D
Note: Use crimp insulated terminals or insulated tubing for wiring these connections. Wires should have a continuous maximum
allowable temperature of 75°C 600 V UL approved vinyl sheathed insulation. Ambient temperature should not exceed 40°C.
Table D.4 Wire Gauge and Torque Specifications (Three-Phase 400 V Class)
2A0360
<1>
R/L1, S/L2, T/L3 240 95 to 300
M12
32 to 40
(283 to 354)
U/T1, V/T2, W/T3 240 95 to 300
–, +1 – 125 to 300
+3 – 70 to 300 M10
18 to 23
(159 to 204)
120 120 to 240 M12
32 to 40
(283 to 354)
2A0415
<1>
R/L1, S/L2, T/L3 120 × 2P 95 to 300
M12
32 to 40
(283 to 354)
U/T1, V/T2, W/T3 300 95 to 300
–, +1 – 150 to 300
+3 – 70 to 300 M10
18 to 23
(159 to 204)
120 120 to 240 M12
32 to 40
(283 to 354)
<1> Drive models CIMR-T2A0110 and 2A0415 require the use of closed-loop crimp terminals for UL/cUL compliance. Use only the tools
recommended by the terminal manufacturer for crimping.
Model
CIMR-T
Terminal
Recommended Gauge
mm
2
Applicable
Gauge
mm
2
Screw
Size
Tightening
Torque
Nxm (lb.in.)
4A0002
4A0004
R/L1, S/L2, T/L3 2.5 2.5 to 6
M4
1.2 to 1.5
(10.6 to 13.3)
U/T1, V/T2, W/T3 2.5 2.5 to 6
–, +1, +2 – 2.5 to 6
B1, B2 – 2.5 to 6
2.5 2.5 to 4
4A0005
4A0007
4A0009
R/L1, S/L2, T/L3 2.5 2.5 to 6
M4
1.2 to 1.5
(10.6 to 13.3)
U/T1, V/T2, W/T3 2.5 2.5 to 6
–, +1, +2 – 2.5 to 6
B1, B2 – 2.5 to 6
2.5 2.5 to 6
4A0011
R/L1, S/L2, T/L3 2.5 2.5 to 6
M4
1.2 to 1.5
(10.6 to 13.3)
U/T1, V/T2, W/T3 2.5 2.5 to 6
–, +1, +2 – 2.5 to 6
B1, B2 – 2.5 to 6
2.5 2.5 to 6
4A0018
R/L1, S/L2, T/L3 2.5 2.5 to 16
M4
1.2 to 1.5
(10.6 to 13.3)
U/T1, V/T2, W/T3 2.5 2.5 to 16
–, +1, +2 – 4 to 16
B1, B2 – 4 to 6
2.5 2.5 to 6 M5
2 to 2.5
(17.7 to 22.1)
4A0023
R/L1, S/L2, T/L3 4 2.5 to 16
M4
1.2 to 1.5
(10.6 to 13.3)
U/T1, V/T2, W/T3 4 2.5 to 16
–, +1, +2 – 4 to 16
B1, B2 – 4 to 6
44 to 6M5
2 to 2.5
(17.7 to 22.1)
4A0031
R/L1, S/L2, T/L3 6 6 to 16
M5
2 to 2.5
(17.7 to 22.1)
U/T1, V/T2, W/T3 6 6 to 16
–, +1, +2 – 6 to 16
B1, B2 – 6 to 10
2 to 2.5
(17.7 to 22.1)
66 to 10M6
4 to 6
(35.4 to 53.1)
4A0038
R/L1, S/L2, T/L3 10 10 to 16
M5
2 to 2.5
(17.7 to 22.1)
U/T1, V/T2, W/T3 6 6 to 16
–, +1, +2 – 6 to 16
B1, B2 – 6 to 10
2 to 2.5
(17.7 to 22.1)
10 6 to 16 M6
4 to 6
(35.4 to 53.1)
Model
CIMR-T
Terminal
Recommended Gauge
mm
2
Applicable
Gauge
mm
2
Screw
Size
Tightening
Torque
Nxm (lb.in.)