E.3 User Setting Table
500 YASKAWA ELECTRIC SIEP C710616 30B YASKAWA AC Drive T1000A Technical Manual
L8-12 Ambient Temperature Setting
L8-15 oL2 Characteristics Selection at Low Speeds
L8-18 Software Current Limit Selection
L8-27 Overcurrent Detection Gain
L8-29 Current Unbalance Detection (LF2)
L8-32
Main Contactor and Cooling Fan Power Supply Failure
Selection
L8-35 Installation Method Selection
L8-38 Carrier Frequency Reduction Selection
L8-40 Carrier Frequency Reduction Off Delay Time
L8-41 High Current Alarm Selection
L8-46 AVR Function Selection
L8-55 Internal Braking Transistor Protection
L8-93 Pull-Out Detection Time at Low Speed
L8-94 Pull-Out Detection Level at Low Speed
L8-95 Average Pull-Out Frequency at Low Speed
n1-01 Hunting Prevention Selection
n1-02 Hunting Prevention Gain Setting
n1-03 Hunting Prevention Time Constant
n1-05
Hunting Prevention Gain while in Reverse
n2-01
Speed Feedback Detection Control (AFR) Gain
n2-02
Speed Feedback Detection Control (AFR) Time Constant 1
n2-03
Speed Feedback Detection Control (AFR) Time Constant 2
n3-13
Overexcitation Deceleration Gain
n3-14
High Frequency Injection during Overexcitation
Deceleration
n3-21 Overslip Suppression Current Level
n3-23 Overexcitation Operation Selection
n5-01 Feed Forward Control Selection
n5-02 Motor Acceleration Time
n5-03 Feed Forward Control Gain
n6-05 Online Tuning Gain
n8-01 Initial Rotor Position Estimation Current
n8-02 Pole Attraction Current
n8-35 Initial Rotor Position Detection Selection
n8-45
Speed Feedback Detection Control Gain
n8-47 Pull-In Current Compensation Time Constant
n8-48
Pull-In Current
n8-49
d-Axis Current for High Efficiency Control
n8-51
Acceleration/Deceleration Pull-In Current
n8-54
Voltage Error Compensation Time Constant
n8-55 Load Inertia
n8-57 High Frequency Injection
n8-62 Output Voltage Limit
n8-65
Speed Feedback Detection Control Gain during ov
Suppression
n8-69 Speed Calculation Gain
n8-84 Polarity Judge Current
n9-10 AVR Time Constant
n9-12 On-Delay Compensation Time
n9-62 On-Delay Compensation Derating Start Frequency
n9-63 On-Delay Compensation Disable Frequency
o1-01
Drive Mode Unit Monitor Selection
o1-02
User Monitor Selection After Power Up
o1-03 Digital Operator Display Selection
o1-04 V/f Pattern Display Unit
o1-10 User-Set Display Units Maximum Value
No. Name
User
Setting
o1-11 User-Set Display Units Decimal Display
o2-01 LO/RE Key Function Selection
o2-02 STOP Key Function Selection
o2-03 User Parameter Default Value
o2-04 Drive Model Selection
o2-05 Frequency Reference Setting Method Selection
o2-06
Operation Selection when Digital Operator is
Disconnected
o2-07 Motor Direction at Power Up when Using Operator
o3-01 Copy Function Selection
o3-02 Copy Allowed Selection
o4-01 Cumulative Operation Time Setting
o4-02 Cumulative Operation Time Selection
o4-03 Cooling Fan Maintenance Operation Time Setting
o4-05 Capacitor Maintenance Setting
o4-07 DC Bus Pre-charge Relay Maintenance Setting
o4-09 IGBT Maintenance Setting
o4-11 U2, U3 Initialize Selection
o4-12 kWh Monitor Initialization
o4-13 Number of Run Commands Counter Initialization
S1-01
Disturb Function Selection
S1-02
Disturb Function Amplitude
S1-03
Disturb Step
S1-04
Disturb Deceleration Time
S1-05
Disturb Acceleration Time
S2-01
Frequency Reference Gain
S2-02
Frequency Reference Gain Change Ramp
S3-01 Braking Transistor Operation Selection
S3-02 Braking Transistor Operation Voltage Level
S3-03 Output Voltage Gain Selection
S3-04
Output Voltage Gain Change Time
S4-01 KEB Mode Selection
S4-02
KEB Start/End Voltage
S4-03
KEB Start Voltage
S4-04
KEB Start dV/dt level
S4-05
KEB Start dV/dt filter
S4-06
KEB End Voltage
S4-07
KEB End Detection Time
S4-08
KEB 1 Phase Loss Detection Level
S4-09
KEB 1 Phase Loss Sampling Time
S4-10
KEB 1 Phase Loss Detection Time
S4-11 KEB Target Voltage
S4-12
KEB Hold Time
S4-13
KEB Minimum Operation Time
S4-14
KEB Reacceleration Prohibit Frequency
S4-15
KEB Supply Loss Detection Selection
S5-01
KEB Decel Time 1
S5-02
KEB Decel Time 2
No. Name
User
Setting
To Next Page
Loading...
