EasyManuals Logo

Zebra DS6878 Product Reference Guide

Zebra DS6878
528 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #55 background imageLoading...
Page #55 background image
Maintenance, Troubleshooting & Technical Specifications 3 - 5
Digital Scanner emits a
low/high/low/high beep sequence
while it is being programmed.
Out of ADF parameter storage
space.
Erase all rules and re-program with
shorter rules.
Digital Scanner emits long low/long
high beeps.
Input error, incorrect bar code or
Cancel
bar code was scanned.
Scan the correct numeric bar codes
within range for the parameter
programmed.
Page timeout; remote device is
out of range/not powered.
Move the digital scanner back into
range of the remote device; try to
re-connect; check remote device
configuration.
Digital Scanner emits long low/long
high/long low/long high beeps.
Out of host parameter storage
space.
Scan
Default Parameters on page
5-5
.
Out of memory for ADF rules. Reduce the number of ADF rules or the
number of steps in the ADF rules.
Connection attempt was rejected
by remote device.
Free up remote device resources.
Digital Scanner emits
high/high/high/low beeps.
RS-232 receive error. Normal during host reset. Otherwise,
set the digital scanner's RS-232 parity
to match the host setting.
Digital Scanner emits high/low
beeps.
The digital scanner is buffering
Code 39 data.
Or
Keyboard parameter selected.
Normal.
Or
Enter value using bar code keypad.
Bluetooth disconnection event. Move the digital scanner back into
range of the remote device.
In Master (SPP) mode, re-pair the
digital scanner and cradle by scanning
the
PAIR
bar code on the cradle; check
cradle power.
In Slave (SPP/HID) mode, reestablish
connection between the digital scanner
and remote device from the remote
device side.
Digital Scanner emits three long high
beeps.
Code 39 buffer is full. Scan the Code 39 bar code without a
leading space or scan
Do Not Buffer
Code 39
on
Code 39 Buffering - Scan
& Store on page 15-39
to transmit
stored Code 29 data.
Digital Scanner emits four high
beeps on trigger release.
Low battery. Place digital scanner in cradle to
charge the battery.
Table 3-1
Troubleshooting (Continued)
Problem Possible Causes Possible Solutions

Table of Contents

Other manuals for Zebra DS6878

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Zebra DS6878 and is the answer not in the manual?

Zebra DS6878 Specifications

General IconGeneral
Wavelength655 nm
Scanner type2D
Yaw reading angle-60 - 60 °
Decoding standards1D, 2D, PDF417, PDF417, microPDF417, Composite Codes (CC-A, CC-B, CC-C), U.S. Postnet and Planet, U.K., Japan, Australian, Netherlands KIX code, Royal Mail 4 State Customer, UPU ICS 4 State Postal, USPS 4CB, TL C-39, Aztec (Standard, Inverse), MaxiCode, DataMatrix/ECC 200 (Standard, Inverse), QR Code (Standard, Inverse and Micro)
Tilt reading angle-360 - 360 °
Input voltage5 V
BluetoothYes
Dimensions (WxDxH)69 x 97 x 185 mm
CertificationFCC, RoHS
Product colorBlack
International Protection (IP) codeIP43
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 50 °C
Operating relative humidity (H-H)5 - 95 %
Cables includedUSB
Weight and Dimensions IconWeight and Dimensions
Weight238 g

Related product manuals