Cisco Catalyst 3560-X User Manual

1-21
Catalyst 3750-X and 3560-X Switch Software Configuration Guide
OL-25303-03
Chapter 1 Overview
Default Settings After Initial Switch Configuration
• DNS is enabled. For more information, see Chapter 1, “Administering the Switch.”
• TACACS+ is disabled. For more information, see Chapter 1, “Configuring Switch-Based
Authentication.”
• RADIUS is disabled. For more information, see Chapter 1, “Configuring Switch-Based
Authentication.”
• The standard HTTP server and Secure Socket Layer (SSL) HTTPS server are both enabled. For more
information, see Chapter 1, “Configuring Switch-Based Authentication.”
• IEEE 802.1x is disabled. For more information, see Chapter 1, “Configuring IEEE 802.1x
Port-Based Authentication.”
• Port parameters
– Operating mode is Layer 2 (switchport). For more information, see Chapter 1, “Configuring
Interface Characteristics.”
– Interface speed and duplex mode is autonegotiate. For more information, see Chapter 1,
“Configuring Interface Characteristics.”
– Auto-MDIX is enabled. For more information, see Chapter 1, “Configuring Interface
Characteristics.”
– Flow control is off. For more information, see Chapter 1, “Configuring Interface
Characteristics.”
– PoE is autonegotiate. For more information, see Chapter 1, “Configuring Interface
Characteristics.”
• VLANs
– Default VLAN is VLAN 1. For more information, see Chapter 1, “Configuring VLANs.”
– VLAN trunking setting is dynamic auto (DTP). For more information, see Chapter 1,
“Configuring VLANs.”
– Trunk encapsulation is negotiate. For more information, see Chapter 1, “Configuring VLANs.”
– VTP mode is server. For more information, see Chapter 1, “Configuring VTP.”
– VTP version is Version 1. For more information, see Chapter 1, “Configuring VTP.”
– No private VLANs are configured. For more information, see Chapter 1, “Configuring Private
VLANs.”
– Voice VLAN is disabled. For more information, see Chapter 1, “Configuring Voice VLAN.”
• IEEE 802.1Q tunneling and Layer 2 protocol tunneling are disabled. For more information, see
Chapter 1, “Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling.”
• STP, PVST+ is enabled on VLAN 1. For more information, see Chapter 1, “Configuring STP.”
• MSTP is disabled. For more information, see Chapter 1, “Configuring MSTP.”
• Optional spanning-tree features are disabled. For more information, see Chapter 1, “Configuring
Optional Spanning-Tree Features.”
• Flex Links are not configured. For more information, see Chapter 1, “Configuring Flex Links and
the MAC Address-Table Move Update Feature.”
• DHCP snooping is disabled. The DHCP snooping information option is enabled. For more
information, see Chapter 1, “Configuring DHCP Features and IP Source Guard.”
• IP source guard is disabled. For more information, see Chapter 1, “Configuring DHCP Features and
IP Source Guard.”

Cisco Catalyst 3560-X Specifications

General

Enclosure Type	Rack-mountable - 1U
Subtype	Gigabit Ethernet
Ports	48 x 10/100/1000 + 4 x SFP
Flash Memory	64 MB
Power Device	Internal power supply
Voltage Required	AC 120/230 V (50/60 Hz)
Operating System	Cisco IOS
Device Type	Switch
Performance	Switching capacity: 128 Gbps
Jumbo Frame Support	Yes
Routing Protocol	RIP-1, RIP-2, EIGRP
Remote Management Protocol	SNMP 1, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, HTTP, HTTPS
Features	DHCP support, VLAN support, QoS, IPv6 support, Syslog
Compliant Standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad, IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ag, IEEE 802.3at
Stacking	Stackable
Security Features	SSH, RADIUS, TACACS+
Management	CLI
Dimensions (H x W x D)	17.5 in
Operating Temperature	32 to 113 °F (0 to 45 °C)
Humidity	10 - 95% (non-condensing)